Troubleshooting | Toshiba DP-1810 specs

TROUBLESHOOTING

This chapter describes how to release a paper jam, how to replace a toner cartridge and how to settle other trouble.

When Message Lamp is Lit/Blinking	72
Paper Jams	75
Checking position of paper jams	75
Paper jams within Automatic Document Feeder (optional) (Lower)	76
Paper jams within Automatic Document Feeder (optional) (Upper)	78
Paper jams on bypass tray	80
Paper jam behind transfer unit	81
Paper jams within fuser unit	82
Paper jams within Paper Feed Unit (optional)	84
Replacing Toner Cartridge	85
Before Calling Service Technician	90
General operation	90
Toner-related items	91
Original/Copy paper-related items	91
Image trouble	92

Image 73

Toshiba DP-1810 manual Troubleshooting, When Message Lamp is Lit/Blinking Paper Jams

Contents

Operators Manual for Copying Functions Page Preface Preface FCC Notice Before Reading This Manual How to read this manual Symbols in this manual Trademarks Description of original/paper direction Contents Switching Operation Sound On/Off Adjusting Density LevelChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/Blinking 105 Daily Inspection Cleaning charger Cleaning transfer charger Contents Recommended toner cartridges Toshiba Quality Is Second to NoneCartridge detecting function Toner remaining check function Toner Supplies / PartsGeneral When installing or moving General Precautions 31.5 Other points When using the equipment Position of Certification label, etc When handling supplies During maintenance or inspection First-aid measures Poration Disclaimer Notice Low power mode Energy saving featuresSleep mode / Super sleep mode Environmental Information Description of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Front / Right side Description of Each ComponentPlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020 Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheet Configuration of options Control panel Density adjustment buttons/lamps Original mode button/lampsOriginal setting lamp Interrupt button/lamp Original button/lamps Copy button/lampsAPS/AMS selecting button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF Press the power switch to on side Types of energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving mode Super sleep mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Paper types not acceptable Recommended paperStoring paper Media type Product name Press down the paper plate Placing paper in drawers Widen the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper size Register the paper size into the equipment Do not let your fingers be caught when closing the drawer Registering standard size LD, LT, LT-R, LG, ST-R Preparation 3 Registering Size of Paper Placed Code No Registering other standard sizes Press the Start button Placing Originals Using Bypass TrayMaking Copies Placing Originals Setting position Type of origiAcceptable originals Maximum number of originals scanned in one go Placing originals on the original glass Placing booklet-type originals such as books or catalogs Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weight Placing originals on Automatic Document Feeder optional When placing a large amount of originals with a long width Check if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as required When the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copying Press the Interrupt button Interrupting copying and making another copy Interrupt copy Media type Paper size Maximum sheet Capacity *1 Using Bypass Tray Bypass copying Paper size has been registered Placed on the bypass tray is lit Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default Settings Automatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APS Place paper in the drawer Place the original Manual paper selection Selecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming in button until Zooming In/Out Copy Image Press the Sort button Copying in Same Page Order as Originals Sort Copying Button Sort buttonOriginal is scanned Repeat this until all originals have been scanned Copying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode Dark Settings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/Off Checking Total Number Copied Switch the display to check the rest of the total numberPress and hold Button for more than two seconds Press Button to switch the enabled mode Changing of the Enabled Energy Saving ModeAuto sleep time Zooming in button to change When Message Lamp is Lit/Blinking Paper Jams Troubleshooting Cover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lamp Recommended toner cartridges Paper jam lamp Service call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Paper jams within Automatic Document Feeder optional Lower When releasing jammed paperOpen the Automatic Document Feeder Do not tear jammed paper Paper Jams Raise the lever and open the upper cover Paper jams within Automatic Document Feeder optional Upper Paper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Paper Jams Paper jams within Paper Feed Unit optional Open the front cover Hold down the green lever Replacing Toner CartridgeNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related items Image trouble Before Calling Service Technician Page Daily Inspection Maintenance and Inspection Original glass Guides Platen sheet Daily Inspection Open the front cover Clean the charger Cleaning charger Cleaning transfer charger Daily Inspection Page Specifications of Options 104 STUDIO181 Specifications 102Continuous copying speed 103 Packing list OPC STUDIO181 Specifications Packing list Continuous copying speedPaper size Feeder Continuous Copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Index 102 Page Multifunctional Digital Systems