Changing of the Enabled Energy Saving Mode | Toshiba DP-1810

4 SETTINGS AND MANAGEMENT OF EQUIPMENT

Changing of the Enabled Energy Saving Mode

The settings of the enabled energy saving mode and auto sleep time (time until entering the mode) can be changed.

1	Press and hold the	button for more than two seconds.
	The present mode name (Sleep mode: SLP or Super sleep mode: SPS) is displayed in

the LED display for approx. 2 seconds, and then the current auto sleep time is displayed. e.g.) Auto sleep time: 15 minutes in the super sleep mode

2	Press the	button to switch the enabled mode.
	The mode is switched each time you press the button, and the selected mode name is
	displayed in the LED display for approx. 2 seconds.
3	Press the	(zooming out) or	(zooming in) button to change
	the auto sleep time.

The auto sleep time (1 to 240 minutes / 24 steps) is switched each time you press the button, and the specified time is displayed in the LED display.

4 Press the [START] button.

The LED display returns to the normal one.

70 Changing of the Enabled Energy Saving Mode

Image 72

Toshiba DP-1810 manual Changing of the Enabled Energy Saving Mode, Press Button to switch the enabled mode, Auto sleep time

Contents

Operators Manual for Copying Functions Page Preface Preface FCC Notice How to read this manual Symbols in this manual Before Reading This Manual Description of original/paper direction Trademarks Contents Adjusting Density Level Switching Operation Sound On/OffChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/Blinking Daily Inspection Cleaning charger Cleaning transfer charger 105 Contents Toshiba Quality Is Second to None Recommended toner cartridgesCartridge detecting function Toner remaining check function Supplies / Parts TonerGeneral General Precautions When installing or moving Other points 31.5 When using the equipment Position of Certification label, etc During maintenance or inspection When handling supplies First-aid measures Disclaimer Notice Poration Energy saving features Low power modeSleep mode / Super sleep mode Environmental Information Preparation 1 Turning Power on Description of Each ComponentPreparation 2 Placing Copy Paper Description of Each Component Front / Right sidePlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020 Left side / Inner side USB terminal 4-pin Receiving tray Scanning areaOriginal scale Platen sheet Configuration of options Control panel Original mode button/lamps Density adjustment buttons/lampsOriginal setting lamp Interrupt button/lamp Copy button/lamps Original button/lampsAPS/AMS selecting button/lamps Preparation 1 Turning Power on Turning power onTurning power OFF Press the power switch to on side Saving energy when not in use Energy saving mode Types of energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving mode Super sleep mode Preparation 2 Placing Copy Paper Acceptable media typesFeeder Media type Paper size Maximum sheet Capacity *1 Recommended paper Paper types not acceptableStoring paper Media type Product name Placing paper in drawers Press down the paper plate Widen the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawer Do not let your fingers be caught when closing the drawer Register the paper size into the equipment Preparation 3 Registering Size of Paper Placed Registering standard size LD, LT, LT-R, LG, ST-R Registering other standard sizes Code No Press the Start button Using Bypass Tray Placing OriginalsMaking Copies Setting position Type of origi Placing OriginalsAcceptable originals Maximum number of originals scanned in one go Placing originals on the original glass Placing booklet-type originals such as books or catalogs Using Automatic Document Feeder optional Precautions for Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weight When placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optional Making Copies Check if paper is placed in the drawerPlace the original Select the copy modes as required When the number of sheets exiting has exceeded When the paper has run outStopping/Resuming copying Press the CLEAR/STOP button during scanning or copying Interrupting copying and making another copy Interrupt copy Press the Interrupt button Using Bypass Tray Media type Paper size Maximum sheet Capacity *1 Bypass copying Placed on the bypass tray is lit Paper size has been registered Default Settings Paper Selection Zooming In/Out Copy ImageAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installation Paper Selection Automatic paper selection APSPlace the original on the Automatic Document Feeder Automatic paper selection APS Manual paper selection Place paper in the drawer Place the original Selecting the drawer of the equipment Zooming In/Out Copy Image Automatic magnification selection AMSAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming in button until Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Press the Sort button Sort button ButtonOriginal is scanned Repeat this until all originals have been scanned Copying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode Adjusting Density Level To adjust the density to the desired levelTo return it to the automatic copy density mode Dark Settings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound off Switch the display to check the rest of the total number Checking Total Number CopiedPress and hold Button for more than two seconds Changing of the Enabled Energy Saving Mode Press Button to switch the enabled modeAuto sleep time Zooming in button to change Troubleshooting When Message Lamp is Lit/Blinking Paper Jams When Message Lamp is Lit/Blinking Cover open lampPaper empty lamp Toner lamp Paper jam lamp Recommended toner cartridges Service call lamp When paper jams occur frequently Paper JamsChecking position of paper jams When releasing jammed paper Paper jams within Automatic Document Feeder optional LowerOpen the Automatic Document Feeder Do not tear jammed paper Paper Jams Paper jams within Automatic Document Feeder optional Upper Raise the lever and open the upper cover Paper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass tray Paper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side cover Paper Jams Paper jams within Paper Feed Unit optional Replacing Toner Cartridge Open the front cover Hold down the green leverNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Before Calling Service Technician General operationPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related items Image trouble Before Calling Service Technician Page Maintenance and Inspection Daily Inspection Daily Inspection Original glass Guides Platen sheet Cleaning charger Open the front cover Clean the charger Cleaning transfer charger Daily Inspection Page STUDIO181 Specifications 102 Specifications of Options 104Continuous copying speed 103 Packing list STUDIO181 Specifications OPC Continuous copying speed Packing listPaper size Feeder Continuous Copying speed Specifications of Options Automatic Document FeederPaper Feed Unit Index 102 Page Multifunctional Digital Systems