Cleaning charger | Toshiba DP-1810 guide

Cleaning charger

If the inside of the charger is dirty, staining may appear on the copied image. Clean the charger following the procedure below.

1 Open the front cover.

2 Clean the charger.

Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three times.

Check if the cleaning knob is fully inserted after cleaning.

3 Close the front cover.

Daily Inspection 97

Image 99

Toshiba DP-1810 manual Cleaning charger, Open the front cover Clean the charger

Contents

Operators Manual for Copying Functions Page Preface Preface FCC Notice Before Reading This Manual How to read this manual Symbols in this manual Trademarks Description of original/paper direction Contents When Message Lamp is Lit/Blinking Adjusting Density LevelSwitching Operation Sound On/Off Changing of the Enabled Energy Saving Mode 105 Daily Inspection Cleaning charger Cleaning transfer charger Contents Toner remaining check function Toshiba Quality Is Second to NoneRecommended toner cartridges Cartridge detecting function Supplies / Parts TonerGeneral When installing or moving General Precautions 31.5 Other points When using the equipment Position of Certification label, etc When handling supplies During maintenance or inspection First-aid measures Poration Disclaimer Notice Environmental Information Energy saving featuresLow power mode Sleep mode / Super sleep mode Preparation 1 Turning Power on Description of Each ComponentPreparation 2 Placing Copy Paper Automatic Document Feeder optional, MR-2020 Description of Each ComponentFront / Right side Platen Cover optional, KA-1650PC Left side / Inner side Platen sheet USB terminal 4-pinReceiving tray Scanning area Original scale Configuration of options Control panel Interrupt button/lamp Original mode button/lampsDensity adjustment buttons/lamps Original setting lamp Copy button/lamps Original button/lampsAPS/AMS selecting button/lamps Press the power switch to on side Preparation 1 Turning Power onTurning power on Turning power OFF Canceling conditions for energy saving mode Saving energy when not in use Energy saving modeTypes of energy saving mode To turn the equipment into the energy saving mode manually Super sleep mode Preparation 2 Placing Copy Paper Acceptable media typesFeeder Media type Paper size Maximum sheet Capacity *1 Media type Product name Recommended paperPaper types not acceptable Storing paper Press down the paper plate Placing paper in drawers Widen the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper size Register the paper size into the equipment Do not let your fingers be caught when closing the drawer Registering standard size LD, LT, LT-R, LG, ST-R Preparation 3 Registering Size of Paper Placed Code No Registering other standard sizes Press the Start button Using Bypass Tray Placing OriginalsMaking Copies Maximum number of originals scanned in one go Setting position Type of origiPlacing Originals Acceptable originals Placing originals on the original glass Placing booklet-type originals such as books or catalogs Media types Maximum size Maximum number Paper weight Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional When black streaks appear on the copied image Placing originals on Automatic Document Feeder optional When placing a large amount of originals with a long width Select the copy modes as required Making CopiesCheck if paper is placed in the drawer Place the original Press the CLEAR/STOP button during scanning or copying When the number of sheets exiting has exceededWhen the paper has run out Stopping/Resuming copying Press the Interrupt button Interrupting copying and making another copy Interrupt copy Media type Paper size Maximum sheet Capacity *1 Using Bypass Tray Bypass copying Paper size has been registered Placed on the bypass tray is lit Default Settings Paper Selection Zooming In/Out Copy ImageAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default Settings Automatic paper selection APS Paper SelectionAutomatic paper selection APS Place the original on the Automatic Document Feeder Place paper in the drawer Place the original Manual paper selection Selecting the drawer of the equipment Specifying reproduction ratio manually Zooming In/Out Copy ImageAutomatic magnification selection AMS Automatic magnification selection AMS If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Zooming in button until Specifying reproduction ratio manuallyPress Zooming out or Desired reproduction ratio appears Zooming In/Out Copy Image Press the Sort button Copying in Same Page Order as Originals Sort Copying Repeat this until all originals have been scanned Sort buttonButton Original is scanned Copying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode Dark Adjusting Density LevelTo adjust the density to the desired level To return it to the automatic copy density mode Settings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/Off Switch the display to check the rest of the total number Checking Total Number CopiedPress and hold Button for more than two seconds Zooming in button to change Changing of the Enabled Energy Saving ModePress Button to switch the enabled mode Auto sleep time When Message Lamp is Lit/Blinking Paper Jams Troubleshooting Toner lamp When Message Lamp is Lit/BlinkingCover open lamp Paper empty lamp Recommended toner cartridges Paper jam lamp Service call lamp When paper jams occur frequently Paper JamsChecking position of paper jams Do not tear jammed paper When releasing jammed paperPaper jams within Automatic Document Feeder optional Lower Open the Automatic Document Feeder Paper Jams Raise the lever and open the upper cover Paper jams within Automatic Document Feeder optional Upper Paper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Paper Jams Paper jams within Paper Feed Unit optional Replacing Toner Cartridge Open the front cover Hold down the green leverNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Before Calling Service Technician General operationPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related items Image trouble Before Calling Service Technician Page Daily Inspection Maintenance and Inspection Original glass Guides Platen sheet Daily Inspection Open the front cover Clean the charger Cleaning charger Cleaning transfer charger Daily Inspection Page STUDIO181 Specifications 102 Specifications of Options 104Continuous copying speed 103 Packing list OPC STUDIO181 Specifications Continuous copying speed Packing listPaper size Feeder Continuous Copying speed Specifications of Options Automatic Document FeederPaper Feed Unit Index 102 Page Multifunctional Digital Systems