Toshiba E6581830 1. Overview , 2. Basic specifications

E658130

- 4 -

1. Overview

The option allows the VF-S15 drive to be connected into a CC-Link network. CC-Link supports a

maximum of 42 nodes, allowing for the Master and this option is based on CC-Link V1.1 and V2.0.

The CCL-003Z is able to operate RUN/STOP, monitor the status of the drive, set the drive’s parameter

and etc. by the CC-Link master through installing the VF-S15. And it can use various applications.

2. Basic specifications

<Environmental specification>

Item Specification

Operating

environment

Indoors, an altitude of 3,000m or less, where the product will not be exposed

to direct sunlight, corrosive or explosive gasses, vapor, coarse particulates

including dust and where there is no grinding fluid or grinding oil nearby.

Ambient

temperature

0 to + 60 degreeC

Storage

temperature

-25 to +65 degreeC

Related

temperature

20 to 93% (no condensation and absence of vapor)

Vibration 5.9 m/s2 (0.6G) or less (10 – 55Hz)

<CC-Link communication and option specification>

Item Specification

Number of units

corrected

42 units max. (1 station occupied by 1 unit). May be used with other

equipment.

Baud rate 156k, 625k, 2.5M, 5M, 10Mbps

Power supply Supplied from SBP009Z

Station type Remote device station

Number of stations

occupied

Ver.1: occupies one station, V2: occupies one station (selectable from among

double, quadruple and octuple)

Connect cable CC-Link dedicated cable,

CC-Link V1.10 compatible CC-Link dedicated cable

Contents

Main option unit Function Manual CCL003Z Introduction will be unavailable for a while. Table of Contents 1. Overview 2. Basic specifications 2.1. CC-Link Version 2.1.1. CC-Link Ver. 1.10 2.1.2. CC-Link Ver. 2 3. Names and functions The drawing below shows names and functions of main parts. 3.1. Outline 4. Installation on inverter 4.1. Connection cable 4.2. Terminating resistor 4.3. Connection of CC-Link master unit and inverter I M E658130 - 9 - 4.4. The maximum connection number of units E658130 - 10 - 4.5. LED indicator E658130 - 12 - 5. Functions 5.1. Initial setting 12, 13: - 14: E658130 - 13 - 5.2. Communication parameters for CCL003Z 5.3. CC-Link function setting 5.3.1. Station number setting 5.3.2. Baud rate setting 5.3.3. CC-Link extended setting E658130 - 16 - 5.4. Basic functions 5.4.1. Run and frequency operation command 5.4.2. Monitor 5.4.3. Writing and reading the parameter E658130 5.5. I/O signal list 5.5.1. One station is occupied (CC-Link Ver.1) (c122=0) E658130 - 18 - 5.5.2. Double setting is selected (CC-Link Ver.2) (c122=1) 5.5.3. Quadruple setting is selected (CC-Link Ver.2) (c122=2) E658130 - 19 - 5.5.4. Octuple setting is selected (CC-Link Ver.2) (c122=3) 5.5.5. Trip history E658130 - 21 - 5.5.6. Detail of input and output signals ** Set OFF (0) to reserved bit. E658130 - 22 - E658130 * The bit described " Reserved " is unstable. Don't use the Reserved " bit for the judgment. - 23 - E658130 - 24 - 5.5.7. Remote Register Assignment E658130 - 25 - E658130 - 26 - 2. Remote register (Inverter -> Master) E658130 - 27 - E658130 - 28 - 5.5.8. Instruction Codes Page E658130 - 30 - 5.5.9. The details of an error code Page 5.5.10. Description of reply code E658130 - 33 - 5.5.11. Description of monitor code E658130 - 34 - 5.5.12. Description of input terminal information 5.5.13. Description of output terminal information 6. Programming examples E658130 - 36 - E658130 - 37 - E658130 - 38 - 6.1. Program example for reading the inverter status Example SW80.1: Station 2 ready Example 1 shows a ladder logic to read the inverter status. Remote input Station1 Station 2 6.2. Program example for setting the operation mode 6.3. Program example for setting the operation commands 6.4. Program example for setting the running frequency 6.5. Program example for monitoring the output frequency 6.6. Program example for parameter writing E658130 - 43 - 6.7. Program example for parameter reading Example 7 Write f311 read code (1311H) to Turn on the instruction code execution E658130 - 44 - 6.8. Program example for trip information reading Example 6.9. Program example for resetting the inverter at inverter error 6.10. Instructions 7. Unusual diagnosis 7.1. Option error 7.2. Disconnection error of network cable E658130 - 48 - 7.3. How to check the error using the LEDs CPU Unit 1. When One Inverter Is Connected Master P S 2.When two or more inverters are connected Master CPU Unit P S 3. Communication stops during operation Terminal resistors are left un-connected. (L.RUN may put out the light.) Check that the terminal resistors are connected.