Manuals / Toshiba / Computer Equipment / Laptop

Toshiba PSLD1X, PSLD2X, PSLD3X manual Installing the LCD Module

Models: PSLD1X PSLD3X PSLD2X

1 201

Download 201 pages 24.26 Kb

Page 189

Installing the LCD Module

4.15 LCD Module

4 Replacement Procedures

Installing the LCD Module

NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module.

Install the LCD module according to the following procedures and Figures 4-29, 4-30.

1.Turn the LCD upside down.

2.Connect the LCD/FL cable to the LCD module connector.

3.Turn the LCD right side up.

4.Place the LCD bracket in the correct position and secure it with two M2x3 black flat head screws on each side.

5.Please the LCD module in the correct position and secure it with two M2.5x5 black flat heat screws on each side.

CAUTION: When installing the LCD module, please follow below instruction:

When plug in LCD/FL cable into LCD module connector, need to plug horizontally. For Sharp panel, if LCD/FL cable connector is not plugged horizontally, it may be damaged.

Satellite L350/ Satellite Pro L350/ EQUIUM L350/ SATEGO L350 Maintenance Manual

4-51

Image 189

Toshiba PSLD1X, PSLD2X, PSLD3X manual Installing the LCD Module

Contents

Toshiba Personal Computer Satellite L350 Satellite Pro L350 Maintenance ManualEQUIUM L350 SATEGO L350 PSLD0x/PSLD1x PSLD2x/PSLD3xCopyright DisclaimerTrademarks Preface SAFETY PRECAUTIONSThe manual is divided into the following parts Acronyms ConventionsKeys Key operationTroubleshooting Table of ContentsChapter Hardware OverviewChapter Diagnostic ProgramsAudio Record Test Chapter 4 Replacement ProceduresColors of Screw Shanks Page Removing the CCD and MIC Appendices Chapter 1 Hardware Overview 1 Hardware Overview Contents Chapter1 Hardware Overview Tables Figures1.1 Features Using the following sizes of memory modules y 512 MB 32M⋅16⋅8P/667MHz ‰ Keyboard The keyboard has 30 kinds’ countries keyboard ‰ Battery ‰ On-Board LAN Figure 1-1 ID Parts Description Placement 1.1 Features Figure 1-2 Computer Block Diagram1 Hardware Overview 1.1 Features Figure 1-3 System Board Configurations1 Hardware Overview Page Figure 1-4 is Block Diagram of the System Unit Figure 1-4 System Unit Block Diagram1.2 System Unit Components The system unit of the computer consists of the following components y 8Mb x 1 chip 1024KB flash parts − NvStorage Size 128KB − Enhanced Power Management − Manageability ‰ Battery EEPROM 1B1.2 System Unit Components 1 Hardware Overview− IEEE 802.11agn y Data Rate − IEEE 802.11g Standard 54M bps − IEEE 802.11ag Standard 54M bps − IEEE 802.11agn Standard 130M bps1.3 2.5-inch HDD Figure 1-5 SATA HDD Table 1-1 HDD SpecificationsTable 1-2 Combo CD-RW/DVD-ROM Drive Specifications 1.4 Combo CD-RW/DVD-ROMFigure 1-6 Combo CD-RW/DVD-ROM Drive 1.5 DVD Super Multi +-R Double Layer Table 1-3 DVD Super Multi Drive Specifications1.6 HD DVD ROM Table 1-4 HD DVD ROM Drive Specifications1.7 Power Supply 1.1.1 Main Battery Table 1-5 Battery Specifications1.1.2 Battery Charging Control 1.8 BatteriesTable 1-6 Quick/Normal Charging Time 1.1.3 RTC Battery2 Troubleshooting Chapter TroubleshootingContents ChapterMessage Check Procedure 1 Test Program Check 2 TroubleshootingAudio Test Cooling ModuleFigures 2 TroubleshootingTables 2-iv2 Troubleshooting 2.1 Outline2.1 Outline 2.2 Basic Flowchart 2.2 Basic Flowchart 2 TroubleshootingFigure 2-1 Basic Flowchart 1/2 Figure 2-1 Basic Flowchart 2/2 If the diagnostic program cannot detect an error, the error may be intermittent. Run the continuous test program repeatedly to isolate the problem. Check the log utilities function to confirm which diagnostic test detected the error, then perform the appropriate troubleshooting procedures as follows Procedure 1 Power Icon Check 2.3 Power Supply‰ DC IN LED AC power cord Procedure 2 Connection CheckBattery pack Procedure 3 Replacement Check2.4 System Board Procedure 1 Message CheckProcedure 2 Test Program Check Procedure 3 Replacement Check1. System test 2. Memory test 3. Keyboard test 4. Display test Insert system disk in drive Press any key when ready Or Procedure 1 Message CheckNon-System disk or disk error Replace and press any key Procedure 2 Partition CheckProcedure 3 Format Check Check 5 Use the SYS command in the DOS system to install system filesStatus CodeSystem board Procedure 5 Connector Check and Replacement CheckProcedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check2.6 Keyboard KeyboardProcedure 2 Test Program Check Procedure 1 External Monitor CheckProcedure 3 Connector Check and Replacement Check 2.7 DisplayFL inverter board Check 3 The FL may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform CheckSystem board LCD/FL cableProcedure 2 Test Program Check Procedure 1 ODD Cleaning CheckProcedure 3 Connector Check and Replacement Check ConnectorCheck 3 The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check2.9 LAN Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check2.10 Audio Test SpeakerProcedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check2.11 Cooling Module Cooling module2 Troubleshooting 2.11Cooling Module2-23 Chapter Diagnostic Programs 3 Diagnostic Programs ContentsChapter Quick StartVideo Error Codes and descriptionCommunication COMM Quick Test Item ListPage 3.1 General NOTE 1 This Diagnostic supports phoenix10SNOTE 2 Before running a test, be sure to 1. Check that all the cables are connected securely… A Formatted FLOPPY DISK 3.2 Quick Start 3.2.1 Quick Test3.2.2 Customization Test The test result will be displayed in the following screen CPU Speed Test Step by Step 3. Test Result 3.2.3 Keyboard Layout test 3.2.5 Audio Play Test 3.2.4 Hotkey Test3.2.6 Audio Record Test 3.2.7 DMI Read3.2.8 DMI Write The confirmation screen is as below 3.2.9 System Information NOTE Setup All of DMI Information in Type is Max 32 Digital3.2.10 View Logs 1. Diagnostics Windows 3.2.12 The Diagnostics Screen Explanation3.2.11 Exit to Free DOS 2. Test Running Status and Report Panel‹ Program Name and Its Version Service Diagnostic Ver1.10 3. USER BREAK4. Title Bar ‹ Pause Enable Display ‘PAUSE’ when “Pause Enable” is enabled 3.3 Options 3.3.1 OverviewOptions Menu Notes 3 Diagnostic Programs 3.3.2 Batch Parameters Configuration3.3 Option 9 Break On Error 9 Wait On Error9 Pause Enable 9 Monitor Battery Life3.3.3 Item’s Parameters Configuration 9 Monitor CPU Thermal Monitor the CPU temperature Test Mode9 LOOPBOUND 9 TIMEBOUNDInteractive Parameters3.3.4 Load Batch Parameters 3.3.5 Save Batch Parameters Log Options 9 Log Errors 3.3.6 LOG Parameters Setting9 Log Errors Only 9 Log Errors Only with Time9 Log Device Info on Fail 9 Append to Old Log FileLog file Name 3.3.7 Specify LOG Viewer↑, ↓ 3.3.9 LOG ViewerPage Up, Page Down Ctrl+Home Module Name Service Diagnostic Ver 1.00 ... Memory Tester Build DateCtrl+End Ctrl+F3Error Code Module Name Service Diagnostic Ver 1.00 ... Mouse Test Build DateError Message Touch Pad Test Fail End Time Wed Jul 05 104916 Base Memory TestTest 3.4 SubtestsSubtest TestPage 3.4 Subtests 3 Diagnostic ProgramsSubtest 01 CPU 3.5 System Test9 NPU Interrupt Test 9 NPU Basic Functions TestSubtest 03 FAN Speed Test Subtest 02 Boards3 Diagnostic Programs parameter setting dialog window3.5 System Test Subtest 01 BIOS ROM 3.6 Memory TestSubtest 02 Parity 3 Diagnostic Programs 3.6 Memory TestSubtest 03 Patterns Subtest 04 Extended Pattern 3 Diagnostic Programs 3.6 Memory TestSubtest 05 Walking 1’s Test Subtest 07 Address Test Subtest 06 Walking 0’s TestSubtest 08 Refresh Test Subtest 09 Cache MemorySubtest 12 Memory Speed Test This test item is to check whether the data bus works normallyPassword：hard disk 3.7 StorageSubtest 01 HDD Percent-Specify the coverage rate in percentage of the total disk 3.7 Storage 3 Diagnostic ProgramsSubtest 02 ODD Subtest 3.8 Video1. Text in normal attribute 2. Text in blinking normal attribute 4. Text Color 3 Diagnostic Programs Subtest 02 640 * 480 VGA Mode3.10 Peripheral NOTE 1 If the VESA Can’t Support The Mode ,The Mode Will Display Gray Subtest 03 VESA Video ModesSubtest 04 VESA Video Memory Subtest 06 LCD Panel Test Subtest 05 AGP TestRegister Test 3.10 Peripheral 3 Diagnostic ProgramsSubtest Direct Color TestSubtest 11 BitBlt Engine Test 3 Diagnostic Programs 3.10 PeripheralNOTE 1AMD platform can’t support this Test item Subtest 01 LAN Card 3.9 Communication COMM3.10 Peripheral 1. Led Test Check whether the Device led works normally Error 3.11 Error Codes and descriptionCommon Error Description03xx BoardThe PC speakers sound source 3 Diagnostic Programs 3.11Error Codes and Description34xx 04xxAudio 31xx08xx LAN CardMouse 05xx20xx IDE-HDDPage 3.12 Quick Test Item List 3.12 Quick Test Item List3 Diagnostic ProgramsDevice Test ItemsChapter Replacement Procedures 4-ii 4 Replacement Procedures4 Replacement Procedures Chapter 4 Contents4 Replacement Procedures Installing the LCD Module Installing the FL Inverter BoardInstalling the CCD and MIC Installing the Speakers4 Replacement Procedures 4 Replacement Procedures 4.1 General Safety Precautions 4.1 General Before You Begin Assembly Procedures Disassembly Procedures4.1 General 4 Replacement ProceduresTools and Equipment Screw Tightening TorqueSymbols of Screws on the Computer Body Symbol examplesColors of Screw Shanks Figure 4-1 Removing the battery pack Removing the Battery PackInstalling the Battery Pack Figure 4-2 Removing the PC card Removing the Optional PC CardInstalling the Optional PC Card Figure 4-3 Removing the memory card Removing the Memory CardInstalling the Memory Card Figure 4-4 Removing the optional memory Removing the Optional MemoryInstalling the Optional Memory Removing the HDD 4.2 HDDFigure 4-5 Removing the HDD pack HDD cover HDD cover secure screw HDD packM3x4 Black flat head screw HDD HDD chassisM3x4 Black flat head screw Figure 4-6 Removing the HDD chassisInstalling the HDD 4.3 ODD Bay Module Removing the ODD Bay ModuleFigure 4-7 Removing the ODD bay module Installing the ODD Bay Module Disassembling the ODD Drive Figure 4-8 Removing the bracket from the ODD driveAssembling the ODD Drive 4.4 Keyboard Removing KeyboardFigure 4-9 Removing the keyboard 4 Replacement Procedures Installing the Keyboard4.4 Keyboard 4.5 MDC Module Removing the MDC ModuleFigure 4-10 Removing the MDC module Installing the MDC Module 4.6 Wireless LAN Card Removing the Wireless LAN CardFigure 4-11 Removing the wireless LAN card Installing the Wireless LAN Card 4.7 Top Cover Removing the Top CoverFigure 4-12 Removing the screws from the bottom of the computer Installing the Top Cover 4 Replacement Procedures4.7 Top Cover Figure 4-13 Removing the top cover4.8 Display Assembly Removing the Display AssemblyFigure 4-14 Removing the screws from the back of the computer Installing the Display Assembly and ODD Extended Board Figure 4-15 Removing the display assembly4.9 System Board, AC-IN Cable and ODD Extended Board Removing the System Board, AC-IN Cable and ODD Extended BoardFigure 4-16 Removing the system board Installing the System Board, AC-IN Cable and ODD Extended Board Removing the CPU Cooling Module and Fan For Intel CPU 4.10 CPU Cooling Module and FanFigure 4-18 Removing the CPU cooling module Figure 4-17 Removing the fan4-35 M2.5x5 white flat head screw Fan CN501 TapeFigure 4-19 Applying silicon grease Installing the CPU Cooling Module and FanFor Intel CPURemove the CPU cooling module and FanFor AMD CPU Figure 4-21 Removing the CPU cooling module Figure 4-20 Removing the fanCPU cooling module bracket M2x3 white flat head screwFigure 4-22 Applying silicon grease Installing the CPU Cooling Module and FanFor AMD CPU4.11 CPU Removing the CPUFigure4-23 Removing the CPU Figure 4-24 Installing the CPU Installing the CPU4-42 Figure 4-25 Securing the CPU4.12 Broadcom Card Removing the Broadcom CardFigure 4-26 Removing the Broadcom card Installing the Broadcom Card 4.13 Display Mask Removing the Display MaskFigure 4-27 Removing the display mask 4 Replacement Procedures Installing the Display Mask4.13 Display Mask 4.14 FL Inverter Board Removing the FL Inverter BoardFigure 4-28 Removing the FL inverter board Installing the FL Inverter Board Removing the LCD module 4.15 LCD Modules4.15 LCD Module 4 Replacement ProceduresFigure 4-29 Removing the LCD module and screws Figure 4-30 Removing the LCD moduleInstalling the LCD Module 4.16 CCD Board and MIC Removing the CCD Board and MICFigure 4-31 Removing the CCD board and MIC Installing the CCD Board and MIC 3. Seat the CCD module, MIC in the correct position4-53 4.17 Speakers Installing the SpeakersRemoving the Speakers Figure 4-32 Removing the speakers4.18 Power Button Board and Switch Board Removing the Power Button Board and Switch BoardFigure 4-33 Removing the power button board and switch board Install the Power Button Board and Switch Board 4.19 Touch Pad and Button Board Removing the Touch Pad and Button BoardFigure 4-34 Removing the touch pad and button board Installing the Touch Pad and Button Board 4.20 USB cable, CRT cable and RJ11 Cable Removing the USB cable, CRT cable and RJ11 CableFigure 4-35 Removing the USB cable, CRT cable and RJ11 Cable Installing the USB cable, CRT cable and RJ11 Cable Appendices Appendix Contents