Toshiba TDP-EX20 Displaying Information Status display, Detailed description Fan mode, Key lock

Using the menus 1 (Continued)

Default setting 2 menu

Item		Description
Projection	Sets projection mode in accordance with Placement Style. p.23
mode	(Standard)	(Rear)	(Ceiling)	(Rear ceiling)
Fan mode	Sets the cooling fan speed.		Standard	High

Remote control When 2 projectors are used and controlled by the remote control respectively, this menu sets the code for the projector and the remote control.

[ or : Enter setting] [: Select from 1, 2] [: Confirm]

[:Select OK to end] Press [Cancel] to return.

Key lock	Lock the control panel buttons.
	[ or	: Enter setting] [	: Select On/Off] [	: Confirm]
	[	:Select OK to end]
	Press [Cancel] to return.
Lamp power	Set the lamp power.			Low	Standard
Reset all	Press . (The password and user logo are not reset.)
	Resets all adjustments and settings to their factory settings. Yes				No
Password	Password setting p.35
	Press	. Password registration/Password setting

Detailed description [Fan mode]

Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500 meters above sea level).

• Do not set Fan mode to [High] when using the projector at a lower altitude.

[Remote control]

Sets a remote control code from 2 types. You can set each code respectively for up to 2 projectors. The factory setting is [1].

To switch codes, set the same code for the projector and the remote control. A remote control code is applied after the setting is done.

•You cannot operate the remote control if the codes of the projector and the remote control do not match.

Remote control code setting for remote control

Set the same remote control code switch as the projector. p.18 p.19

[Key lock]

Protect from operating errors by locking on the control panel buttons of the projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly operation with the control panel buttons is disabled.

•To release the key lock, set the [Key lock] to [Off] using remote control. Pressing the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in orange for 3 seconds, and at the same time the projector beeps.) However, when Network or USB memory input is selected, the [Key lock] cannot be set to [Off] with the [RETURN] button on the projector.

[Lamp power]

When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter.

N Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

			“Yes”: displayed, “No”: not displayed
Item	Description	Computer	Y/PB/PR	Video	S-video	Network	USB
							memory
Input	Input source name	Yes	Yes	Yes	Yes	Yes	Yes
								Operations
Mode name	RGB input mode [Note 1]	Yes	No	No	No	No	No
Resolution	Resolution (in dots)	Yes	No	No	No	No	No
Frequency	Sync frequency	Yes	No	No	No	No	No
Sync	Sync signal polarity [Note 2]	Yes	No	No	No	No	No
Signal format	Y/PB/PR signal format	No	Yes	No	No	No	No
Video mode	Color method of video signal	No	No	Yes	Yes	No	No
Lamp time	Time of lamp use [Note 3]	Yes	Yes	Yes	Yes	Yes	Yes
Lamp reset count	The count for lamp replacement	Yes	Yes	Yes	Yes	Yes	Yes
Total time	The total time that this projector is	Yes	Yes	Yes	Yes	Yes	Yes
	used.
Version	Firmware version [Note 4]	Yes	Yes	Yes	Yes	Yes	Yes

Notes

1:The mode of supported RGB signals p.94 is shown.

2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a dealer about getting replacement for:

TLPLW15 for TDP-EX20 (sold separately).

4:[Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc.

Note

•The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again.

44 45