II. By PIN | TP-Link TL-WR941ND specs

TL-WR941N/TL-WR941ND

Wireless N Router

Step 2: Choose Press the button of the new device in two minutes and click Connect..

Step 3: For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the QSS as below, and click Next.

The QSS Configuration Screen of Wireless Adapter

II. By PIN

If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.

Method One: Enter the PIN into my Router

Step 1: Keep the default QSS Status as Enabled and click the Add device button in Figure 4-2,then the following screen will appear.

- 18 -

Image 23

TP-Link TL-WR941ND manual II. By PIN

Contents

TL-WR941N TL-WR941ND Copyright & Trademarks FCC Statement Country Restriction Reason/remark FCC RF Radiation Exposure Statement Contents Dhcp Package Contents Overview of the Router Introduction Conventions Main Features Name Status Indication Panel LayoutFront Panel Rear Panel ¾ Reset button System Requirements Connecting the RouterInstallation Environment Requirements Connecting the Router Hardware Installation of the TL-WR941ND Wireless N Router TCP/IP configuration Quick Installation Guide Please check the connection following these steps Success result of Ping command 3Login the router Quick Installation Guide Choose WAN Connection Type Quick Setup Static IP 10 Quick Setup Finish Status Configuring the RouterLogin Router Status Quick Setup Method One Quick Secure Setup functionQSS By PBC Add a New Device Method Two II. By PIN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND 2 WAN Network1 LAN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND WAN PPPoE PPPoE Advanced Settings MAC Clone Wireless 12 Wireless Settings Wireless Settings Wireless Security TL-WR941N/TL-WR941ND Encryption You can select either Automatic, or Tkip or AES 14 Wireless MAC address Filtering Wireless MAC Filtering 15 Add or Modify Wireless MAC Address Filtering entry To access for Filtering Rules Wireless Advanced 17 The router attached wireless stations Wireless Statistics Dhcp Dhcp Settings 20 Dhcp Clients List Dhcp Clients List To modify or delete an existing entry Address ReservationTo Reserve IP addresses Delete ForwardingVirtual Servers 25 Add or Modify a Virtual Server Entry To setup a virtual server entry Port Triggering 27 Add or Modify a Triggering Entry To assign a computer or server to be a DMZ server 3 DMZUPnP Firewall Security IP Filtering ¾ Enable Firewall the general firewall switch is on or off To add/modify an IP Address filtering entry TL-WR941N/TL-WR941ND Domain Filtering Other configurations for the entries 35 Add or Modify a Domain Filtering entry To Add a Domain filtering entry To add or modify a Domain Filtering entry MAC Filtering To add additional entries, repeat steps Static Routing 38 Static Routing To add static routing entries Dynamic DNS 40 Dyndns.org Ddns Settings System Tools Time SettingTo configure the system manually Firmware To configure the system automatically Backup & Restore Factory Defaults Password Reboot System log 47 Password Statistics Remote Management TCP Statistics Table Figure A-2 PPPoE Connection Mode Appendix a FAQ Want to use Netmeeting, what do I need to do? Figure A-3 MAC Clone Want to build a WEB Server on the LAN, what should I do? Figure A-5 Add or Modify a Virtual server Entry Figure A-7 Remote Management Wireless stations cannot connect to the router TL-WR941N/TL-WR941ND Install TCP/IP component Appendix B Configuring the PCs Shown in the Figure below Figure B-3 ¾ Setting IP address manually Figure B-4 Environmental and Physical Appendix C SpecificationsWireless General Appendix D Glossary TL-WR941N/TL-WR941ND