PPPoE Advanced Settings | TP-Link TL-WR941ND manual

TL-WR941N/TL-WR941ND

Wireless N Router

If you want to do some advanced configurations, please click the Advanced button, and the page shown in Figure 4-9will then appear:

Figure 4-9 PPPoE Advanced Settings

¾MTU Size - The default MTU size is “1492” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP.

¾Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.

¾ISP Specified IP Address - If your ISP does not automatically assign IP addresses to the router during login, please click “Use IP address specified by ISP” check box and enter the IP address provided by your ISP in dotted-decimal notation.

¾Detect Online Interval - The router will detect Access Concentrator online at every interval. The default value is “0”. You can input the value between “0”and “120”. The value “0” means no detect.

¾DNS IP address - If your ISP does not automatically assign DNS addresses to the router during login, please click “Use the following DNS servers” check box and enter the IP address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well.

Click the Save button to save your settings.

- 25 -

Image 30

TP-Link TL-WR941ND manual PPPoE Advanced Settings

Contents

TL-WR941N TL-WR941ND Copyright & Trademarks FCC Statement FCC RF Radiation Exposure Statement Country Restriction Reason/remark Contents Dhcp Package Contents Introduction Overview of the Router Main Features Conventions Panel Layout Front PanelName Status Indication ¾ Reset button Rear Panel Connecting the Router Connecting the RouterInstallation Environment Requirements System Requirements Hardware Installation of the TL-WR941ND Wireless N Router Quick Installation Guide TCP/IP configuration Success result of Ping command Please check the connection following these steps Quick Installation Guide 3Login the router Choose WAN Connection Type Quick Setup Static IP 10 Quick Setup Finish Configuring the Router LoginStatus Quick Setup Router Status By PBC Quick Secure Setup functionQSS Method One Method Two Add a New Device II. By PIN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND Network 1 LAN2 WAN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND WAN PPPoE PPPoE Advanced Settings Wireless MAC Clone Wireless Settings 12 Wireless Settings Wireless Security TL-WR941N/TL-WR941ND Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 14 Wireless MAC address Filtering 15 Add or Modify Wireless MAC Address Filtering entry Wireless Advanced To access for Filtering Rules Wireless Statistics 17 The router attached wireless stations Dhcp Settings Dhcp Dhcp Clients List 20 Dhcp Clients List Address Reservation To Reserve IP addressesTo modify or delete an existing entry Forwarding Virtual ServersDelete To setup a virtual server entry 25 Add or Modify a Virtual Server Entry Port Triggering 27 Add or Modify a Triggering Entry 3 DMZ UPnPTo assign a computer or server to be a DMZ server Security Firewall ¾ Enable Firewall the general firewall switch is on or off IP Filtering To add/modify an IP Address filtering entry TL-WR941N/TL-WR941ND Other configurations for the entries Domain Filtering To Add a Domain filtering entry 35 Add or Modify a Domain Filtering entry MAC Filtering To add or modify a Domain Filtering entry Static Routing To add additional entries, repeat steps To add static routing entries 38 Static Routing 40 Dyndns.org Ddns Settings Dynamic DNS Time Setting To configure the system manuallySystem Tools To configure the system automatically Firmware Factory Defaults Backup & Restore Reboot Password 47 Password System log Remote Management Statistics Statistics Table TCP Appendix a FAQ Figure A-2 PPPoE Connection Mode Figure A-3 MAC Clone Want to use Netmeeting, what do I need to do? Figure A-5 Add or Modify a Virtual server Entry Want to build a WEB Server on the LAN, what should I do? Wireless stations cannot connect to the router Figure A-7 Remote Management TL-WR941N/TL-WR941ND Appendix B Configuring the PCs Install TCP/IP component Shown in the Figure below ¾ Setting IP address manually Figure B-3 Figure B-4 General Appendix C SpecificationsWireless Environmental and Physical Appendix D Glossary TL-WR941N/TL-WR941ND