Manuals / Tyan Computer / Computer Equipment / Computer Hardware

Tyan Computer Transport GS12 System Assembly Flowchart, System Memory Install Hard Disk Drive

Models: Transport GS12 B5103G12S2

1 87

Download 87 pages 28.49 Kb

Page 14

Image 14

System Assembly Flowchart

The following flowchart shows the basic procedures of system assembly:

START

REMOVE CABINET COVER

INSTALL

CPU AND HEATSINK

INSTALL

SYSTEM MEMORY

INSTALL

HARD DISK DRIVE

CONNECT HARD DISK

DRIVE CABLE

AND POWER CORD

CHECK IF ALL PARTS

ARE PROPERLY CONNECTED

REPLACE

CABINET COVER

FINISH

http://www.TYAN.com

Page 14

Image 14

Tyan Computer Transport GS12 manual System Assembly Flowchart, Start Remove Cabinet Cover Install Cpu And Heatsink Install

Contents

B5103G12S2 RevisionTransport GS12 Software Installation Table of ContentsHardware Installation Introduction5 BIOS Setup 4 Using the LCD Console6 Using RAID and ASF Appendix System Parts ReplacementExpanding the System Safety Precautions Before You BeginPage 1.1 Unpacking IntroductionAnd the following accessories 1.2 Specifications NOTE Specifications are subject to change without noticeComponent 1.3 System ViewFront View DescriptionŽ Power Switch Rear ViewPower Connector LAN1 ConnectorPage Start Hardware InstallationCabinet Cover CPU and Heatsink System Assembly Hard Disk Drive DIMM Rack MountingSYSTEM MEMORY INSTALL HARD DISK DRIVE System Assembly FlowchartSTART REMOVE CABINET COVER INSTALL CPU AND HEATSINK INSTALL CONNECT HARD DISK DRIVE CABLE AND POWER CORD CHECK IF ALL PARTSInstalling the CPU 2.1 System AssemblySafety Considerations Opening the CoverPage Installing System Memory Installing a Hard Disk Drive Page With a Secondary Ultra ATA/100 Hard Disk Drive Installed 2.2 Adding a CD DriveWithout a Secondary Ultra ATA/100 Hard Disk Drive Installed 2.3 Rack MountingCabinet Slides and Ears Cabinet into the Rack Placing the System 2.4 Setting Up the SystemLocking Tab Making the Connection Page Available on CD Software InstallationDriver Available on CD NOTE The driver CD may have been updated after this User’s Manual was completed. If your CD is different from that described in this chapter, refer to the README files on the CD. These files contain the latest information from the software supplierDriver Chipset Driver 3.1 Installation Instructions for WindowsWindows Installation Notes VGA DriverLCD Driver LAN DriverUSB v.2.0 Driver \LCD\GS12\Windows\driver\LCDDriverchecked.inf and click Open -OKNOTE This driver supports Windows 2000 and Windows XP only Intel Application AcceleratorASF Alert Simulation and Watchdog Drivers \ASF\Windows\driver\ASFSimulation\hwdriverchecked.inf and 4. Run the install.bat program in the \ASF\Windows\service\ directoryASF Alert Standard Format 2.0 SDK Run the ASFtools.msi file in the \ASF\AGENT\TOOLS\ directorySuSE Linux 8.1 Installation Notes 3.2 Installation Instructions for Linux RedHat /SuSE/Turbo LinuxRedHat Linux 9.0 Installation Notes Turbo Linux 8 Installation Notes3. Untar/unzip archive tar zxf e1000-5.2.16.tar.gz #define BOOTKERNELSMP6. Install the module insmod e1000 parameter=value lib/modules/KERNELVERSION/kernel/drivers/net/e1000.oASF Alert Simulation NOTE Ignore any depmod ***Unresolved symbols inWatchdog Driver 3. Untar/unzip archive tar zxf MiSMLLCDxxforyyy.tar.gz3. Untar/unzip archive tar xfvz asfm-x.x.tar.gz 3.3 Installation Instructions for FreeBSDFreeBSD 4.7 Installation Notes cd /usr/src/sys/i386/conf mkdir /root/kernelsifemload=”YES” usr/sbin/config MYKERNEL cd ../../compile/MYKERNEL make depend makemake install vi /etc/rc cp ifem* /usr/src/sys/dev/emdev/em/ifemfxhw.c optional em dev/em/ifemphy.c optional em NOTE For assistance, see the ifconfig main pagedev/em/ifemhw.c optional em 3. Untar/unzip archive tar xfvz MiSMFLCDxx.tar.gz3. Install the driver pkgadd -d INTCGigaE.pkg 3.4 Installation Instructions for SolarisSolaris 9 Installation Notes USB Floppy Drive UsagePage Before You Begin Using the LCD Console4.1 Configuring the System 4.2 Setting the Configuration For Windows KEY PRESS settings under HW Monitor List Configuresettings under Performance List Configure PROMPTKEY PRESS Application Log when an alert occurAdministrative Tools - Event Viewer PROMPTPROMPT 4.3 Setting the Configuration For LinuxKEY PRESS FUNCTIONFUNCTION KEY PRESSPROMPT FUNCTION KEY PRESSPROMPT PROMPT 4.4 Setting the Configuration For FreeBSDKEY PRESS FUNCTIONFUNCTION KEY PRESSPROMPT PROMPT var/log/alertlogfile when an alertKEY PRESS FUNCTIONStarting BIOS Setup BIOS Setup5.1 BIOS Setup Program Main Menu Boot FeaturesLarge Disk Access Mode Select DOS or Other Advanced MenuAdvanced Chipset Control I/O Device ConfigurationSecurity Menu Advanced Processor OptionsPower Menu Monitor MenuBoot Menu Exit MenuJumper 5.2 Resetting BIOS SetupSetting DefinitionRAID Using RAID and ASF6.1 About RAID Creating an Array for Performance RAID 1. Select RAID, then Create Volume Manually6.2 Creating an Array 2. Select RAID 0 under the item Select RAID Level, then click on Next 3. Click on Yes Y to continue4. Click on Create to create the new RAID volume 5. Click on OK to finishCreating a Security Array RAID 2. Select RAID 1 under the item Select RAID Level, then click on Next3. Click on Yes Y to continue 4. Click on Yes Y to continue 6. Click on OK to finish Creating RAID With an Existing Data Drive5. Click on Create to create the new RAID volume 2. Select a source disk, then click on Next Run the ASFtools.msi file in the \ASF\agent\tools\ directory Set Up Management Console6.3 About ASF Check Agent and Management Console Link Page Obtain Traps and Push Messages 1. Run AlertApp to set Heartbeat3. Run AlertApp to load the Security Key to the Agent Remote Control2. Save the Key from Management Console into a floppy disk Page Expanding the System 7.1 Opening the Cover7.2 Installing an Expansion Card 7.3 Adding a Secondary Hard Disk Drive 3. Secure the hard disk drive to the bracket with four bottom screws Page Page System Parts Replacement 8.1 Opening the Cover8.2 Removing the Front Bezel 8.3 Replacing the Button Board8.4 Replacing the Fan 8.5 Replacing the USB Board 8.6 Replacing the LCD Module8.7 Replacing the Power Supply 8.8 Replacing the Blower 8.9 Replacing the Motherboard7. Detach the riser card from the PCI slot on the motherboard Reverse the above sequence when installing the new motherboard6. Detach the DIMM from the socket on the motherboard Page DANISH ADVARSEL AppendixCaution Texts Concerning Lithium Batteries NORWEGIAN ADVARSELHelp Resources Returning Merchandise for ServiceTechnical Support 3. Check the TYAN user group alt.comp.periphs.mainboard.TYANNotice for Canada Document # D1582-100