Interface of Packet Tncs | Vertex Standard VX-177 specs

INTERFACE OF PACKET TNCS

The VX-177may be used for Packet operation, using the optional CT-91Microphone Adapter (available from your Yaesu dealer) for easy interconnection to commonly-avail- able connectors wired to your TNC. You may also build your own cable, using a four- conductor miniature phone plug, per the diagram below.

The audio level from the receiver to the TNC may be adjusted by using the VOL knob, as with voice operation. The input level to the VX-177from the TNC should be adjusted at the TNC side; the optimum input voltage is approximately 5 mV at 2000 Ohms.

Be sure to turn the transceiver and TNC off before connecting the cables, so as to prevent voltage spikes from possibly damaging your transceiver.

When you are operating on Packet, switch the Receive Battery Saver OFF, as the “sleep” cycle may “collide” with the beginning of an incoming Packet transmission, causing your TNC not to receive the full data burst. See page 62 for details regarding Battery Saver setup.

VX-177 OPERATING MANUAL

11

Image 13

Vertex Standard VX-177 manual Interface of Packet Tncs

Contents

Yaesu Europe B.V Vertex Standard Contents General Description Supplied Accessories Accessories & OptionsAvailable Options Controls & Connectors TOP & Front Panels Controls & Connectors LCD PTT Push To Talk Switch Controls & Connectors Side PanelMoni Switch Press F + KEY Controls & Connectors Keypad Functions One step or moves the memory Antenna Installation Installation of AccessoriesInstallation of FNB-83 Battery Pack LOW Battery Indication Battery Charging Installation of FBA-25A Alkaline Battery Case Option Belt Clip Installation Interface of Packet Tncs Adjusting the Audio Volume Level Switching Power on and OFFOperation Squelch Adjustment Tuning DialFrequency Navigation Scanning Direct Keypad Frequency Entry Transmission Changing the Transmitter Power Level Keyboard Locking Advanced Operation Disabling the Keypad Beeper KEYPAD/LCD Illumination RF Squelch Checking the Battery Voltage Repeater Shifts Repeater OperationAutomatic Repeater Shift ARS Manual Repeater Shift Activation Changing the Default Repeater Shifts Checking the Repeater Uplink Input Frequency VFO Split Mode Repeater Operation Ctcss Operation CTCSS/DCS/EPCS Operation DCS Operation Tone Search Scanning Epcs Enhanced Paging & Code Squelch Storing the Ctcss Tone Pairs for Epcs Operation Activating the Enhanced Paging & Code Squelch System CTCSS/DCS/EPCS Bell Operation Tone Calling 1750 HZ Split Tone Operation Storing Independent Transmit Frequencies Odd Splits Memory ModeMemory Storage Home Channel Memory Memory Recall Labeling Memories Deleting Memories Memory Offset Tuning Memory Bank Recall Assigning Memories to a Memory BankRemoving Memories from a Memory Bank Memory Bank Operation Moving Memory Data to the VFO Memory only Mode VX-177 Operating Manual Scanning Setting the Scan-Resume Technique Programmed VFO Scan Manual VFO ScanVFO Scanning Memory Scanning How to Skip Omit a Channel during Memory Scan Operation Preferential Memory Scan Memory Bank Scan Programmable Band Limit Memory Scan PMS Memory Channel Priority VFO PriorityHome Channel Priority Priority Channel Scanning Dual Watch VFO-VFO Dual Watch Priority Revert Mode Band Edge Beeper Automatic Lamp Illumination on Scan Stop VX-177 Operating Manual Emergency Channel Operation Emergency Feature Emergency Automatic ID EAI Feature Emergency Feature Smart Search Operation Setting the Smart Search ModeStoring Smart Search Memories Internet Connection Feature Internet Connection Feature Basic Arts Setup and Operation Arts Alert Beep Options Arts Polling Time Options CW Identifier Setup Manual Dtmf Tone Generation Dtmf OperationDtmf Autodialer To send the telephone number Storing the 3-digit code for the Dtmf Pager Operation Dtmf Pager Operation Requires Optional FTD-7 Activating the Dtmf Pager Storing the ANI code Activating the ANI feature Password Miscellaneous Settings Changing the Channel Steps Programming the KEY Assignments TX Battery Saver Receive Battery Saver Setup Automatic POWER-OFF APO Feature Disabling the TX/BUSY Indicator Busy Channel LOCK-OUT Bclo Transmitter TIME-OUT Timer TOT DCS Code Inversion Changing the TX Deviation Level Reset Procedures Try again Cloning VX-177 Operating Manual ARS SET Menu Mode NET CTCSS/DSC/DTMF/EPCS Setting ANI Set Mode Item 2 AR BEP Set Mode Item 1 APOSet Mode Item 3 AR INT Set Mode Item 4 ARS Set Mode Item 9 CLK.SFT Set Mode Item 8 BSY.LEDSet Mode Item 10 Cwid Set Mode Item 11 CW WRT Set Mode Item 18 ECS.CDR Set Mode Item 17 DT WRTSet Mode Item 19 ECS.CDT Set Mode Item 20 EDG.BEP Set Mode Item 23 INT CD Set Mode Item 22 I NETSet Mode Item 24 INT MR Set Mode Item 25 Lamp Set Mode Item 28 Name Set Mode Item 27 M/T-CLSet Mode Item 29 NM WRT Set Mode Item 30 Pswd Set Mode Item 34 RF SQL Set Mode Item 33 REV/HMSet Mode Item 35 RPT.MOD Set Mode Item 36 PRI.RVT Set Mode Item 40 SCN.LMP Set Mode Item 39 SCN MDSet Mode Item 41 Shift Set Mode Item 42 Skip Set Mode Item 45 Step Set Mode Item 44 SQL.TYPSet Mode Item 46 TN FRQ Set Mode Item 47 TOT Set Mode Item 52 EAI Set Mode Item 51 WID.NARSet Mode Item 53 ANI Set Mode Item 54 ANI.WRT General Specifications Installation of the FTD-7 Dtmf Paging Unit Option Declaration by Manufacturer 0511X-0K