Vision 70/CineWide | Vidikron SERIES 1080p guide

Installation

3.11

Installing and Adjusting the CineWide Anamorphic Lens

Anamorphic Lens Installation ➤ and Adjustment -

Vision 70/CineWide

If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the CineWide anamorphic lens.

It is extremely important that the primary lens is properly adjusted

Note before you install the anamorphic lens. Ensure that the image from

the primary lens is perfectly centered on the screen.

The standard Vision 70/CineWide uses a prismatic-style anamorphic lens. This type of lens compresses the height of the image (as opposed to stretching the width) to achieve a 2.35:1 aspect ratio with a 1.78:1 display device.

The Vision 70/CineWide with AutoScope uses a cylindrical anamorphic lens with a much larger aperture than the prismatic lens used with the standard Vision 70/CineWide.

If you are installing a Vision 70/CineWide with AutoScope, refer to Anamorphic Lens Installation and Adjustment - Vision 70/CineWide with AutoScope on page 35. If you are installing a standard Vision 70/CineWide, continue with the next section.

The standard Vision 70 Anamorphic lens mount kit consists of everything shown in Figure

3-15.Some components shipped with your projector may differ slightly from what is shown in these instructions.

1Anamorphic Lens

2 Base Plate

3Screw, Phillips M6x16mm (4x) and 1/4” Flat Washer (4x)

(not shown; secures Base Plate to bottom of projector)

6Pitch/Y-Adjustment Screw, Phillips

Pan Head, 4-40 x 3/8” (2x) and Fender Washer (2x)

5Vertical Mounting Bracket (2x)

4Yaw/Z-Adjustment Lever (2x) and Fiber Washer (2x)

Figure 3-15. Standard Vision 70 Anamorphic Lens Mounting Assembly

32	Vidikron Vision 70 Series Owner’s Operating Manual

Image 44

Vidikron SERIES 1080p manual Installing and Adjusting the CineWide Anamorphic Lens, Vision 70/CineWide

Contents

Series 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting Operation Serial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This Manual Using This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn to Description, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 70 at a Glance 565 Vision 70 Connector Panel Cable Access Door Open to access connectors Built-In Keypad Vision 70 Remote Control Vision 70 Remote Control On / OFF Source Selection Buttons Comp 1 SD ComponentVID S-Video Comp 2 HD Component Memory Preset Buttons Cursor KeysPicture-In-Picture PIP / Picture-By-Picture PBP Controls VAC V2 Aperture Control Remote Control/Built-In Keypad Functional Comparison Motorized Lens Controls Operation 3InstallationRemote Control Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 70/CineWide or Vision 70/CineWide Installation Considerations Projector Installation OptionsInstallation Type Advantages Considerations Throw Ratios for the Vision 70 Series Throw Range Throw RatioProjector Model Vision Ceiling Installation Floor InstallationVertical and Horizontal Position Folded Optics Installing the Optional CineWide Lens Mount Vision 70/CineWide with AutoScope Lens Motor Bottom View Ceiling Mount Extension Brackets Ceiling mounting plate Vision 70/CineWide with Lens Base Plate Floor Mounting Upright Adjusting the ProjectorMounting the Vision Connections to the Vision Connector Panel AccessConnecting Source RGB Connections 10. Progressive Component Video Connections DTV or Progressive Component YPbPr Source DTV Source DVD Player, VCR Satellite Receiver Etc 11. Composite, S-Video and Component Video Connections Connection 12. RS-232 Control System Connection 14. Connecting the 12-Volt Trigger Output to Other Equipment Turning on the Power Focus Zoom Vertical Lens Shift Installing and Adjusting the CineWide Anamorphic Lens Vision 70/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 70/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using Picture-In-Picture/ Picture-By-Picture PIP/PBP 4OperationSelecting Video Memory Selecting an Aspect Ratio Selecting An Input Source Using the On-Screen Menus Adjust InstallationService Picture Picture Adjust Main Menu Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image Option Aspect Ratio Settings Description Remote Projector Status Installation Exit to return to the previous menu or Menu to exit Service Service Operation Operation Remote Control ISF Calibration ISF Calibration Operation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Correct Vision 70 input Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial Communications Serial Communications Serial Commands Serial Commands 7Specifications Vision 70 Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements Dimensions Regulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 70 Dimensions Vision 70 Dimensions Vidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron