System Information Settings, Setting Description | Vixel 335

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

System Information Settings

The System Informations page displays the switch’s parameters and general configuration settings.

To view the system settings, click System. The System Information page appears.

Figure 3-2.System Information Page

The displayed settings are listed below:

Setting	Description

MAC Address	A unique device address assigned to each switch at the
	factory. Cannot be configured or modified.

Serial Num(ber)	A unique identification number assigned to each switch at the
	factory. Cannot be configured or modified.

IP Address	The current IP Address for the switch.

IP Gateway	The current Gateway address for the switch.

IP Netmask	The current IP Netmask address for the switch.

Speed	The current speed setting for the switch.

Speed Control (Last boot)	The speed setting selected during the last switch power-up.

Speed Control (Next boot)	The speed setting selected for the next switch power-up.

Switching Mode	When "on", allows data to be sent directly to a specified port.
	If "off", the data is sent to every port. Disabling Switching
	Mode may be necessary when passing data to legacy devices.

Blocking ARB	When two ports start a communication session, the Blocking
	ARB is sent to all other ports trying to communicate with
	those ports until the connection is terminated. Blocking ARB
	is only active when the switching mode is on.

14

Image 17

Vixel 335 manual System Information Settings, Setting Description

Contents

InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Introduction FeaturesAbout This Guide Overview InSpeed Technology Fibre Channel Arbitrated Loop Installing the Switch InstallationUnpacking the Switch Performing a Power On Systems Test Using Small Form Factor Pluggable SFP TransceiversSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP Removal Attaching Devices Setting Up the Switch System LEDs Understanding the Switch’s LEDsPower On Port LEDs System LEDs Indication SFP Cascading with Non-Overlapping Zones Cascading Switches Acceptable Single Cascade in Zones 2-12 Only E rv i e w Using the Web ManagerConnecting to the Web Manager Logging On and Off Navigation Resetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager Setting Description System Information Settings Click Change Settings Network Settings Switching Mode Switch SpeedSwitch Identification Blocking ARB Time Settings Downloading the Switch Configuration Firmware Information Firmware Settings Event Log Messages Click Change Firmware Settings FC Switch Information FC Switch Information Detection Indication OS Information CLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information 13.Received Port Utilization Page with Highlighted Zones Value Description 15.Port Information Port Settings 16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description 19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings 21.Policies Change Settings 22.Overlapping Zones Zone Settings 25.Overlapping Zone 1 Information Overlapping Zones Non-Overlapping Zones 26.Overlapping Zone 1 Information Configuration Click Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLI Noz Configuration Task CLI Command Enabling or Disabling Dhcp Requests Changing the Switch’s IP ParametersConfiguring Switch Information Downloading New Firmware Managing the Firmware Message Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination Table Option Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web Password Policy Description Policies Threshold Information Settings Description Action Description Actions Command Description Changing the Switching Mode Number. You can also change the port policies PLL Displaying Ports Enables you to configure control of the port. Select from Resetting the Hardware Resetting the SwitchResetting the Switch to Factory Default Settings Viewing the Event Log Viewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Example noz 25,6,7,8 39,10 Non-Overlapping Zoning Configuration Technical Support Reference Tro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP Issues Appendixes Specification s Appendix a Specifications Vixel Model 335 Operating Conditions Operating Conditions Console Commands CommandsGeneral Commands Browse Commands Show Zone Action Commands URL Event Meaning Action Severity Message Appendix C Event Messages Appendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch information Index