Changing the CLI/Web Password | Vixel 335 instruction

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Note: If you do not remember your password, call your customer service representative.

Changing the CLI/Web Password

One password is used to access both the Web Manager and the Command Line Interface. You can change the password through the Command Line Interface (CLI) only. The password must be between 6 and 25 characters in length.

To change the password:

1.Type pw at the prompt.

2.Enter the current password (the default password is password).

3.Enter the new password.

4.Confirm the new password by re-entering it.

A message appears confirming that the password was saved and activated.

>pw

enter current password: ********

enter new password	:	******
re-enter new password :		******

The new password is saved and activated.

Viewing Management, Policy, and Threshold Settings

The Management Agent menu displays the current settings for the switch parameters, switch policies, and thresholding. To view the current Management Agent settings and a complete list of commands, type mc at the prompt. The Management Agent Menu appears.

MANAGEMENT AGENT 00-10-9b-01-0c-dd

	Product	: Vixel 335 Managed Storage Switch
	Firmware	: 2.01 (build 79)
	Hardware	: 3
	IP address	: 172.16.71.14
	Netmask	: 255.255.240.0
	Default gateway	: 172.16.64.1
	DHCP	: disabled
	Management URL	: http://172.16.71.14
	POLICIES:
(1)	Smart insertion	: enabled
(2)	Bad zone recovery	: disabled
(3)	No data recovery	: disabled
(4)	LIP F8 recovery	: enabled
(5)	LIP on port bypass	: enabled
(6)	Auto cascade	: enabled
(7)	Bypass at max OS err	: disabled
(8)	Bypass at max CRC err	: disabled

(9)Bypass on clock delta err : disabled

(10)	Bypass on	switch stall	: disabled
(11)	Clear conn on sw stall		: disabled
	HW I/F:
	ASIC build number		: 0x0001
(12)	OS error	threshold	: 3	(0x3)
(13)	CRC error	threshold	: 3	(0x3)
(14)	Switch stall threshold		: 65535 (0xFFFF)
(15)	Clk error	thresh (ppm)	: 200 (0xC8)

(16)Clk error prescale (1-16) : 6

(17)Err count thresh (CSecs) : 1000

(18)Bad zone thresh (CSecs) : 500

(19)Bad zone bypass (CSecs) : 10

ACTIONS:

(20)Reset switch

(21)Reset HW

(22)Reset counters

(23)Event log

(24)Fibre Alliance event log

(25)Fibre Alliance event sev : Info

43

Image 46

Vixel 335 manual Changing the CLI/Web Password, Viewing Management, Policy, and Threshold Settings

Contents

InSpeed Model Part Number 00041363-001 Rev. a Table of Contents About This Guide FeaturesIntroduction Overview Fibre Channel Arbitrated Loop InSpeed Technology Unpacking the Switch InstallationInstalling the Switch Small Form-Factor Pluggable SFP Installation Using Small Form Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP Removal Setting Up the Switch Attaching Devices Power On Understanding the Switch’s LEDsSystem LEDs System LEDs Indication Port LEDs SFP Cascading Switches Cascading with Non-Overlapping Zones Acceptable Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerE rv i e w Navigation Logging On and Off Configuration Task Location in Web Manager Configuring the SwitchResetting the Switch System Information Settings Setting Description Network Settings Click Change Settings Switch Identification Switch SpeedSwitching Mode Blocking ARB Downloading the Switch Configuration Time Settings Firmware Settings Firmware Information Click Change Firmware Settings Event Log Messages FC Switch Information FC Switch Information OS Information Detection Indication CLS Port Usage Information 11.Ordered Set Information Page with Highlighted Zones Value Description 13.Received Port Utilization Page with Highlighted Zones Port Settings 15.Port Information 16.Port Information Page with Highlighted Zones Mode Description 18.Cascade Information 19.Cascade Information Page with Highlighted Zones Policy Settings Switch Policy Description 21.Policies Change Settings Zone Settings 22.Overlapping Zones Overlapping Zones 25.Overlapping Zone 1 Information 26.Overlapping Zone 1 Information Configuration Non-Overlapping Zones Click Back to Non-overlapping Zone Info to view the changes Management Using the Command Line Interface CLI Connecting to the CLI Configuration Task CLI Command Noz Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling Dhcp Requests Managing the Firmware Downloading New Firmware Message Action Configuring the Trap Destination Table Edit Trap Destination Menu Active Value NEW Value Option Description Changing the CLI/Web Password Viewing Management, Policy, and Threshold Settings Policies Policy Description Settings Description Threshold Information Actions Action Description Changing the Switching Mode Command Description Number. You can also change the port policies Displaying Ports PLL Enables you to configure control of the port. Select from Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event Log Overlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10 Reference Technical Support Tro ub l e sh oo ti n g Small Form-Factor Pluggable SFP Issues Fibre Channel References Appendixes Appendix a Specifications Specification s Operating Conditions Vixel Model 335 Operating Conditions General Commands CommandsConsole Commands Browse Commands Action Commands Show Zone URL Appendix C Event Messages Event Meaning Action Severity Message Appendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Configuring switch information Index Index