There are no errors in the queue | VXI SVM2608 specs

VXI Technology, Inc.

The aforementioned errors are reported for the following reasons:

NO_ERROR	There are no errors in the queue.
ERROR_UNKNOWN_COMMAND	An unknown command was sent to the
	microprocessor.
ERROR_PRE_GT_SIZE	The value programmed in the Pre-Trigger
	Points register is greater than the value
	programmed in the Sample Points
	register.
ERROR_RESISTANCE_OVER_RANGE	The user attempted to measure a
	resistance greater than the range.
ERROR_UNSTABLE_RESISTANCE	In Auto-Range Resistance mode, the
	resistance is not stable.
ERROR_UNSTABLE_VOLTAGE	In Auto-Range Voltage mode, the voltage
	is not stable.
ERROR_MULTIPLE_TEST_SOURCES	The user attempted to connect several
	sources on the Test Bus.
ERROR_NONVOL_READ	There was an error when trying to read
	the non-volatile calibration memory.
ERROR_NONVOL_WRITE	There was an error when trying to write
	to the non-volatile calibration memory.
ERROR_NONVOL_DEFAULTED	There was an error when trying to read
	the default values from the non-volatile
	calibration memory.
ERROR_FLASH_BURN	Error trying to burn data in the FLASH (a
	common error here would occur when
	loading the firmware for U1 and issuing
	the write flash commands for U20, or
	vice versa).
ERROR_INTERNAL_SOFTWARE	The microprocessor encountered an
	internal software error.
ERROR_QUEUE_OVFL	There were more then five errors in the
	ERROR queue.

48	SVM2608 Programming

Image 48

VXI SVM2608 user manual There are no errors in the queue

Contents

SVM2608 VXI Technology, Inc Table of Contents Self Test Command Warranty Limitation of WarrantyCertification Restricted Rights Legend EMC Steve Mauga, QA Manager Service should only be performed by qualified personnel Terms and SymbolsUse Proper Power Cord Use Proper Power Source Avoid Electric Shock Ground the ProductOperating Conditions Improper Use VXI Technology World Headquarters VXI Technology Cleveland Instrument DivisionVXI Technology Lake Stevens Instrument Division Technical Support VXI Technology, Inc SVM2608 Preface Introduction Overview Scale Acquiring Data Triggering Linear Mode Delayed TriggerPre-Trigger Fifo Mode CommandsCalibrations Test Bus Option SVM2608 Block Diagram SVM2608 Environmental Specifications Physical Description Front Panel Interface Wiring GND CH1I CH3IGND CH1I+ GND CH3I+ Exttrigin CH0I CH2I SVM2608 Specifications Mtbf Option 1 SVM2608-01 VXI Technology, Inc SVM2608 Introduction Calculating System Power and Cooling Requirements Setting the Chassis Backplane Jumpers Setting the Base Address Rotary Switch Locations Example Divide DecimalMSB LSB Switch to C and the front switch to Module INSTALLATION/REMOVAL Device Memory Maps Function OffsetReserved Register Offset SVM2608 A32 Register MAP MS = Most Significant LS = Least Significant 0x72 Command Register Channel 0x74 Databyte Ordering Determining the Register Address Accessing the Registers Description of RegistersSysfailctl Force Trigger, Start Register 0x02 Read & Write INTLVL2HSTRIGSRC2 EXT Trig Slope Timeoutctl ReservedExternal Trigger Level 0x06 Read & Write 2WIREOHMS 4WIREOHMSLINEAR/FIFO ATTN-GAIN1-GAIN0 Sample Rate 0x0C, 0x34, 0x5C, 0x84 Read & Write Sample Rate 0x0E, 0x36, 0x5E, 0x86 Read & WriteKHz Channels 0-3/5 MHz Channels 4-5 LPF Control This bit Sample Rate, High-Speed 0xAC, 0xD4 Read & Write Sample Rate, High-Speed 0xAE, 0xD6 Read & Write Timeout 0x1C, 0x44, 0x6C, 0x94, 0xBC, 0xE4 Read & Write Fifo Data 0x24, 0x4C, 0x74, 0x9C, 0xC4, 0xEC Read Only Fifo Data 0x26, 0x4E, 0x76, 0x9E, 0xC6, 0xEE Read OnlyReserved Registers 0xF8 0xFC Trigger Delay = Microprocessor Commands Measurement Commands Captured Data Calculations Self Test Command Resistance Measurement Offset MethodResistance Measurement Dynamic Method Preset Setting Measurement Commands Example Calibration Commands Sample PointsSample Rate Trigger Event Forced TriggerPage Error Processing There are no errors in the queue Diagnostic Commands Changes become effective the next time the module powers up Example 2 Setting Channel 2 to Acquire 200,000 Samples Examples Example 3 Setting Channel 2 to Pre-acquire 100,000 Samples Timeout Counter = Timeout / Timeout Base Clock Timeout Register = Timeout Base * 213 + Timeout Counter VXI Technology, Inc SVM2608 Programming Appendix a Data Swapping Example VXI Technology, Inc SVM2608 Appendix a Index