Diagnostic Commands | VXI SVM2608 guide

www.vxitech.com

Diagnostic Commands

The following commands in combination with the Self-Test command (see measurement commands section above) help diagnose problems with the board.

0x3000	Read the self-test register.
0x3001	Read the self-test relay register.
0x3002	Read the switch register.
0x3003	Read the trigger inputs.
0x3004	Read the calibrated reference value: 0.945 V.
0x3005	Read the calibrated reference value: -0.945 V.
0x3006	Read the calibrated reference value: 9.45 V.
0x3007	Read the calibrated reference value: -9.45 V.
0x3008	Read the calibrated reference value: 128 Ω.
0x3009	Read the calibrated reference value: 81.92 kΩ.
0x300A	Read self-test measurement values.

0x300B Turn SYSFAIL ON (for diagnostic purposes only). 0x300C Turn SYSFAIL OFF (just for diagnostic purposes).

0x300D	Read the calibrated reference value: 0.1177 V.
0x300E	Read the calibrated reference value: -0.1177 V.
0x300F	Unused.
0x3010	Control the HS self-test relays – all OFF.
0x3011	Turn Channel 4 self-test on (Channel 5 OFF).
0x3012	Turn Channel 5 self-test on (Channel 4 OFF).
0x3013	Turn Channel 4 and Channel 5 self-test on (not normal).

SVM2608 Programming

49

Image 49

VXI SVM2608 user manual Diagnostic Commands

Contents

SVM2608 VXI Technology, Inc Table of Contents Self Test Command Limitation of Warranty WarrantyCertification Restricted Rights Legend Steve Mauga, QA Manager EMC Terms and Symbols Service should only be performed by qualified personnelUse Proper Power Cord Use Proper Power Source Ground the Product Avoid Electric ShockOperating Conditions Improper Use VXI Technology Cleveland Instrument Division VXI Technology World HeadquartersVXI Technology Lake Stevens Instrument Division Technical Support VXI Technology, Inc SVM2608 Preface Overview Introduction Scale Triggering Acquiring Data Delayed Trigger Linear ModePre-Trigger Commands Fifo ModeCalibrations Test Bus Option SVM2608 Block Diagram Physical Description SVM2608 Environmental Specifications GND CH1I CH3I Front Panel Interface WiringGND CH1I+ GND CH3I+ Exttrigin CH0I CH2I Mtbf SVM2608 Specifications Option 1 SVM2608-01 VXI Technology, Inc SVM2608 Introduction Setting the Chassis Backplane Jumpers Calculating System Power and Cooling Requirements Rotary Switch Locations Setting the Base Address Divide Decimal ExampleMSB LSB Module INSTALLATION/REMOVAL Switch to C and the front switch to Function Offset Device Memory MapsReserved Register Offset MS = Most Significant LS = Least Significant SVM2608 A32 Register MAP 0x72 Command Register Channel 0x74 Databyte Ordering Determining the Register Address Description of Registers Accessing the RegistersSysfailctl INTLVL2 Force Trigger, Start Register 0x02 Read & WriteHSTRIGSRC2 EXT Trig Slope Reserved TimeoutctlExternal Trigger Level 0x06 Read & Write 4WIREOHMS 2WIREOHMSLINEAR/FIFO ATTN-GAIN1-GAIN0 Sample Rate 0x0E, 0x36, 0x5E, 0x86 Read & Write Sample Rate 0x0C, 0x34, 0x5C, 0x84 Read & WriteKHz Channels 0-3/5 MHz Channels 4-5 LPF Control This bit Sample Rate, High-Speed 0xAE, 0xD6 Read & Write Sample Rate, High-Speed 0xAC, 0xD4 Read & Write Timeout 0x1C, 0x44, 0x6C, 0x94, 0xBC, 0xE4 Read & Write Fifo Data 0x26, 0x4E, 0x76, 0x9E, 0xC6, 0xEE Read Only Fifo Data 0x24, 0x4C, 0x74, 0x9C, 0xC4, 0xEC Read OnlyReserved Registers 0xF8 0xFC Trigger Delay = Measurement Commands Microprocessor Commands Captured Data Calculations Resistance Measurement Offset Method Self Test CommandResistance Measurement Dynamic Method Example Preset Setting Measurement Commands Sample Points Calibration CommandsSample Rate Trigger Event Forced TriggerPage Error Processing There are no errors in the queue Diagnostic Commands Changes become effective the next time the module powers up Examples Example 2 Setting Channel 2 to Acquire 200,000 Samples Example 3 Setting Channel 2 to Pre-acquire 100,000 Samples Timeout Register = Timeout Base * 213 + Timeout Counter Timeout Counter = Timeout / Timeout Base Clock VXI Technology, Inc SVM2608 Programming Data Swapping Example Appendix a VXI Technology, Inc SVM2608 Appendix a Index