Option 1 SVM2608-01 | VXI instruction

www.vxitech.com

OPTION 1 - SVM2608-01

NUMBER OF CHANNELS

	2
VMEBUS INTERFACE
Address Mode	A32
Data Transfer Mode	D16 or D32
SAMPLING RATE
Range		7.15 Samples/s to 20.0 MSamples/s
Resolution		8.333 ns
Accuracy	1%
MEMORY
	1 MSamples per channel
VOLTAGE MEASUREMENTS
Range	±0.5 V, ±1.0 V, ±2.0 V, ±5.0 V, ±10.0 V, ±20.0 V
Resolution	Range/211
Accuracy	1%
INPUT IMPEDANCE
	1 MΩ or 50 Ω (software selectable)
INPUT MODE
	ac or dc (software selectable)
INPUT FILTER
		5 MHz (-3 dB)
TRIGGER LEVELS
Internal		trigger level determined by selected voltage range (see Voltage Measurement above)
Range
Trigger level resolution		Full scale/211
Level accuracy	1%
External
Range		-10 V to +10 V
Trigger level resolution		4.88 mV
Level accuracy	1%
DELAYED TRIGGER
Range		0 samples to (224 -1) samples
Resolution		1 sample
TRIGGER ACCURACY
	1%
EXTERNAL TRIGGER ACCURACY
	1%
TIMEOUT
Range		10 µs to 227 hrs
Resolution		10 µs to 100 s

WARM-UP TIME

10 min

MTBF

80,000 hrs (based on 20% Ground Mobile, 80% Ground Fixed environment, T ≥ 52°C)

SVM2608 Introduction

21

Image 21

VXI user manual Option 1 SVM2608-01

Contents

SVM2608 VXI Technology, Inc Table of Contents Self Test Command Limitation of Warranty WarrantyCertification Restricted Rights Legend Steve Mauga, QA Manager EMC Terms and Symbols Service should only be performed by qualified personnelUse Proper Power Cord Use Proper Power Source Ground the Product Avoid Electric ShockOperating Conditions Improper Use VXI Technology Cleveland Instrument Division VXI Technology World HeadquartersVXI Technology Lake Stevens Instrument Division Technical Support VXI Technology, Inc SVM2608 Preface Overview Introduction Scale Triggering Acquiring Data Linear Mode Delayed TriggerPre-Trigger Commands Fifo ModeCalibrations Test Bus Option SVM2608 Block Diagram Physical Description SVM2608 Environmental Specifications GND CH1I CH3I Front Panel Interface WiringGND CH1I+ GND CH3I+ Exttrigin CH0I CH2I Mtbf SVM2608 Specifications Option 1 SVM2608-01 VXI Technology, Inc SVM2608 Introduction Setting the Chassis Backplane Jumpers Calculating System Power and Cooling Requirements Rotary Switch Locations Setting the Base Address Example Divide DecimalMSB LSB Module INSTALLATION/REMOVAL Switch to C and the front switch to Function Offset Device Memory MapsReserved Register Offset MS = Most Significant LS = Least Significant SVM2608 A32 Register MAP 0x72 Command Register Channel 0x74 Databyte Ordering Determining the Register Address Accessing the Registers Description of RegistersSysfailctl INTLVL2 Force Trigger, Start Register 0x02 Read & WriteHSTRIGSRC2 EXT Trig Slope Timeoutctl ReservedExternal Trigger Level 0x06 Read & Write 4WIREOHMS 2WIREOHMSLINEAR/FIFO ATTN-GAIN1-GAIN0 Sample Rate 0x0C, 0x34, 0x5C, 0x84 Read & Write Sample Rate 0x0E, 0x36, 0x5E, 0x86 Read & WriteKHz Channels 0-3/5 MHz Channels 4-5 LPF Control This bit Sample Rate, High-Speed 0xAE, 0xD6 Read & Write Sample Rate, High-Speed 0xAC, 0xD4 Read & Write Timeout 0x1C, 0x44, 0x6C, 0x94, 0xBC, 0xE4 Read & Write Fifo Data 0x24, 0x4C, 0x74, 0x9C, 0xC4, 0xEC Read Only Fifo Data 0x26, 0x4E, 0x76, 0x9E, 0xC6, 0xEE Read OnlyReserved Registers 0xF8 0xFC Trigger Delay = Measurement Commands Microprocessor Commands Captured Data Calculations Self Test Command Resistance Measurement Offset MethodResistance Measurement Dynamic Method Example Preset Setting Measurement Commands Sample Points Calibration CommandsSample Rate Trigger Event Forced TriggerPage Error Processing There are no errors in the queue Diagnostic Commands Changes become effective the next time the module powers up Examples Example 2 Setting Channel 2 to Acquire 200,000 Samples Example 3 Setting Channel 2 to Pre-acquire 100,000 Samples Timeout Register = Timeout Base * 213 + Timeout Counter Timeout Counter = Timeout / Timeout Base Clock VXI Technology, Inc SVM2608 Programming Data Swapping Example Appendix a VXI Technology, Inc SVM2608 Appendix a Index