View Port Status, Port status definitions are | Xerox KS-801

6.3 View Port Status

Select [3] from main menu to view all LAN port status. The port status are shown like following table style:

---------------------------------------------

Port	LinkStatus PortControl Speed Duplex FlowControl
[1]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[2]	[Link	]	[Enable ]		[10 ]	[Half]	[Enable]
[3]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[4]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[5]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[6]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[7]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[8]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[9]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
---------------------------------------------
The port status definitions are:
Port Status		States		Interpretation
LinkStatus		Unlink		No active link
		Link		Active link established
PortControl		Disable		Port function is disabled.
		Enable		Port function is enabled.
Speed		100		100Mbps.
		10		10Mbps.
Duplex		Full		Full duplex mode.
		Half		Half duplex mode.
FlowControl		Enable		Flow control function is enabled.
		Disable		Flow control function is disabled.

-30-

Image 30

Xerox KS-801 operation manual View Port Status, Port status definitions are

Contents

10/100 Fast Ethernet Managed Switch with Fiber Connectivity Trademarks Table of Contents Console & Telnet Management Web Management Introduction Features Page Specifications Installing the Switch Packing List Panels Install the Switch into a 19-inch Rack Mounting the SwitchesInstall Rack Mount Brackets Desktop Mounting Network Switched Ports Making Network Connections 10/100BASE-TX Fast Ethernet Switched Ports MDI-X and MDI RJ-45 Connectors Auto-negotiation Capable Manual Configuration10/100BASE-TX Fast Ethernet Ports Auto-speed-sensing Flow Control UTP Cable ConnectionsStraight-through and Crossover UTP Cable Module Connector type Fiber cable Maximum length Fast Ethernet Fiber Slot Fiber Module Top view Fiber Jumper Setting Module Outline Duplex Mode Setting SpecificationsModule Installation Switch supports the following trunk configurations Making Trunk ConnectionsPage Monitored Ports When doing sniffer, configureMaking Sniffer Sniffer Port LED Indicators LED PanelsInterpretation Performing Network Management Management Support Login Port Status Management objects Setting IP Address Console Management Telnet Management Console port does not support modem connectionRefer to for more information Snmp Management Support Console & Telnet Management Select 1 from main menu to set IP address Set IP AddressIP Status Select 2 from main menu to view IP status View Port Status Port status definitions are View Port Counters View STP Status Page Restore Default Values Update Firmware Console Sftp Utility Prompts shown on DOS screen are as follows \WINDOWSSFTP Remote Boot System Processing messages shown on console screen are Start Browser Software and Making Connection Set IP Address for the SwitchWeb Management Web Browser Login to the Switch LoginFactory default Username Admin Factory default Password Page Port Status Port Statistics Administrator Click Basic to view or modify the following settings Basic IP Address settings are IP Address Use scroll bar to view all settings as follows Snmp Entries Snmp settings are Advanced Click Advanced in menu to perform Advanced / Spanning Page Page Value is lower priority. Range 0 Priority is assigned to the switch. The higherMAC address of the switch as a unique identi Fier to the network Blocking The switch enters the Blocking State if a Ports which are enabled can be in one of the followListening Switches send messages to one another Learning The switch enters the Learning State if no Advanced / Trunking Advanced / Sniffer Page Console Port Information Port Controls Security Manager System Manager Click System Manager to perform Tftp Update Firmware Click Apply to start Tftp file transfer operationsPage Remote Boot System