Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 operation manual Click Advanced in menu to perform

Models: KS-801

1 63

Download 63 pages 48.76 Kb

Page 48

Image 48

7.5.2 Advanced

Click [Advanced] in menu to perform:

•	Spanning	: Spanning Tree protocol settings
•	Trunking	: Trunking settings
•	Sniffer	: Sniffer settings

-48-

Page 48

Image 48

Xerox KS-801 operation manual Click Advanced in menu to perform

Contents

10/100 Fast Ethernet Managed Switch with Fiber Connectivity DOC.020419-KS801-KTRADEMARKS CISPR A COMPLIANCECE NOTICE 2. Installing the Switch 4. LED Indicators1. Introduction 3. Making Network Connections6. Console & Telnet Management 7. Web Management1. Introduction 1.1 Features Management Features TFTP - software upgrade capabilityOut-of-band console management via RS232 console port In-band Telnet management over TCP/IP network1.2 Specifications 2. Installing the Switch 2.1 Packing List2.2 Panels Crossover setting switch for 10/100 Port #9LED display for power and all port status Plug-in socket for AC power cord2.3 Mounting the Switches Install Rack Mount BracketsInstall the Switch into a 19-inch Rack Desktop Mounting3.1 Network Switched Ports 3. Making Network ConnectionsPIN# MDI-X Jacks MDI JackCrossover SW Port #9 RJ-453.2 10/100BASE-TX Fast Ethernet Ports Manual ConfigurationAuto-negotiation Capable Auto-speed-sensingFlow Control UTP Cable ConnectionsStraight-through and Crossover UTP Cable CONNECTED DEVICE3.3 Fast Ethernet Fiber Slot Fiber Module Top view Fiber Jumper Setting Fiber Jumper SettingModule Outline Duplex Mode Setting SpecificationsModule Installation 3.4 Making Trunk Connections Refer to Console Telnet management chapter and Web management3. Only one trunk can exist between two switch units Rules2. One trunking port can only belong to one trunk 3.5 Making Sniffer Monitored PortsSniffer Port 4. LED Indicators 4.1 LED Panels4.2 Interpretation 5. Performing Network Management 5.1 Management Support5.2 Management objects Login Port StatusAdministrator Port Statistics5.3 Setting IP Address 5.4 Console ManagementFactory default settings of the Console port 5.5 Web Management 5.6 Telnet Managementhttp//xxx.xxx.xxx.xxx telnet5.7 SNMP Management 5.8 Support6. Console & Telnet Management Factory default Username admin Factory default PasswordThe main menu is shown as follows 6.1 Set IP Address 6.2 IP Status6.3 View Port Status The port status definitions are6.4 View Port Counters XmitAbort6.5 View STP Status PathCostPriority Page 6.6 Restore Default Values Select 6 from main menu to restore factory default settingsFactory default settings are 6.7 Update Firmware Console SFTP UtilityThe steps are 6.8 Remote Boot System 7. Web Management 7.1 Start Browser Software and Making Connection7.2 Login to the Switch Login4. Administrator other management functions 1. Home home page and device image2. Port Status view all port status 3. Port Statistics view all port statistic counters7.3 Port Status 7.4 Port Statistics 7.5 Administrator Click Administrator to perform more management functions as follows7.5.1 Basic Click Basic to view or modify the following settingsIP Address IP Address settings areSNMP Entries Use scroll bar to view all settings as followsThe SNMP settings are 7.5.2 Advanced Click Advanced in menu to performAdvanced / Spanning Page Page MAC Address Click Spanning to view and change Spanning tree protocol settingsPriority Port Number Path CostPort Status PriorityAdvanced / Trunking NonePort 1,2 Port 7,8Advanced / Sniffer Click Update to change sniffer port 7.5.3 Console Port Information BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow Control7.5.4 Port Controls Port Control - enable or disable port functionAuto - Auto-negotiation is enabled 7.5.5 Security Manager Click Security Manager to view or change user name and passwordTFTP Update Firmware Remote Boot System 7.5.6 System ManagerTFTP Update Firmware Page Remote Boot System