Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 Click Administrator to perform more management functions as follows

Models: KS-801

1 63

Download 63 pages 48.76 Kb

Page 43

7.5 Administrator

7.5 Administrator

Click [Administrator] to perform more management functions as follows:

•

•

•

•

•

•

Basic

Advanced

Console Port Information

Port Controls

Security Manager

System Manager

-43-

Image 43

Xerox KS-801 operation manual Click Administrator to perform more management functions as follows

Contents

DOC.020419-KS801-K 10/100 Fast Ethernet Managed Switch with Fiber ConnectivityCISPR A COMPLIANCE TRADEMARKSCE NOTICE 3. Making Network Connections 2. Installing the Switch4. LED Indicators 1. Introduction7. Web Management 6. Console & Telnet Management1. Introduction 1.1 Features In-band Telnet management over TCP/IP network Management FeaturesTFTP - software upgrade capability Out-of-band console management via RS232 console port1.2 Specifications 2.1 Packing List 2. Installing the SwitchPlug-in socket for AC power cord 2.2 PanelsCrossover setting switch for 10/100 Port #9 LED display for power and all port statusDesktop Mounting 2.3 Mounting the SwitchesInstall Rack Mount Brackets Install the Switch into a 19-inch Rack3. Making Network Connections 3.1 Network Switched PortsPort #9 RJ-45 PIN#MDI-X Jacks MDI Jack Crossover SWAuto-speed-sensing 3.2 10/100BASE-TX Fast Ethernet PortsManual Configuration Auto-negotiation CapableCONNECTED DEVICE Flow ControlUTP Cable Connections Straight-through and Crossover UTP Cable3.3 Fast Ethernet Fiber Slot Fiber Jumper Setting Fiber Module Top view Fiber Jumper SettingModule Outline Specifications Duplex Mode SettingModule Installation Refer to Console Telnet management chapter and Web management 3.4 Making Trunk ConnectionsRules 3. Only one trunk can exist between two switch units2. One trunking port can only belong to one trunk Monitored Ports 3.5 Making SnifferSniffer Port 4.1 LED Panels 4. LED Indicators4.2 Interpretation 5.1 Management Support 5. Performing Network ManagementPort Statistics 5.2 Management objectsLogin Port Status Administrator5.4 Console Management 5.3 Setting IP AddressFactory default settings of the Console port telnet 5.5 Web Management5.6 Telnet Management http//xxx.xxx.xxx.xxx5.8 Support 5.7 SNMP ManagementFactory default Username admin Factory default Password 6. Console & Telnet ManagementThe main menu is shown as follows 6.2 IP Status 6.1 Set IP AddressThe port status definitions are 6.3 View Port StatusXmitAbort 6.4 View Port CountersPathCost 6.5 View STP StatusPriority Page Select 6 from main menu to restore factory default settings 6.6 Restore Default ValuesFactory default settings are Console SFTP Utility 6.7 Update FirmwareThe steps are 6.8 Remote Boot System 7.1 Start Browser Software and Making Connection 7. Web ManagementLogin 7.2 Login to the Switch3. Port Statistics view all port statistic counters 4. Administrator other management functions1. Home home page and device image 2. Port Status view all port status7.3 Port Status 7.4 Port Statistics Click Administrator to perform more management functions as follows 7.5 AdministratorClick Basic to view or modify the following settings 7.5.1 BasicIP Address settings are IP AddressUse scroll bar to view all settings as follows SNMP EntriesThe SNMP settings are Click Advanced in menu to perform 7.5.2 AdvancedAdvanced / Spanning Page Page Click Spanning to view and change Spanning tree protocol settings MAC AddressPriority Priority Port NumberPath Cost Port StatusPort 7,8 Advanced / TrunkingNone Port 1,2Advanced / Sniffer Click Update to change sniffer port BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow Control 7.5.3 Console Port InformationPort Control - enable or disable port function 7.5.4 Port ControlsAuto - Auto-negotiation is enabled Click Security Manager to view or change user name and password 7.5.5 Security Manager7.5.6 System Manager TFTP Update Firmware Remote Boot SystemTFTP Update Firmware Page Remote Boot System