Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 operation manual Console Port Information

Models: KS-801

1 63

Download 63 pages 48.76 Kb

Page 57

7.5.3 Console Port Information

7.5.3 Console Port Information

Click [Console Port Information] from Administrator sub-menu to view console port information. They are:

BaudRate (Bit/sec)

Data Bits

Parity Check

Stop Bits

Flow Control

-57-

Image 57

Xerox KS-801 operation manual Console Port Information, BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow Control

Contents

DOC.020419-KS801-K 10/100 Fast Ethernet Managed Switch with Fiber ConnectivityTRADEMARKS CISPR A COMPLIANCECE NOTICE 4. LED Indicators 2. Installing the Switch1. Introduction 3. Making Network Connections7. Web Management 6. Console & Telnet Management1. Introduction 1.1 Features TFTP - software upgrade capability Management FeaturesOut-of-band console management via RS232 console port In-band Telnet management over TCP/IP network1.2 Specifications 2.1 Packing List 2. Installing the SwitchCrossover setting switch for 10/100 Port #9 2.2 PanelsLED display for power and all port status Plug-in socket for AC power cordInstall Rack Mount Brackets 2.3 Mounting the SwitchesInstall the Switch into a 19-inch Rack Desktop Mounting3. Making Network Connections 3.1 Network Switched PortsMDI-X Jacks MDI Jack PIN#Crossover SW Port #9 RJ-45Manual Configuration 3.2 10/100BASE-TX Fast Ethernet PortsAuto-negotiation Capable Auto-speed-sensingUTP Cable Connections Flow ControlStraight-through and Crossover UTP Cable CONNECTED DEVICE3.3 Fast Ethernet Fiber Slot Fiber Module Top view Fiber Jumper Setting Fiber Jumper SettingModule Outline Duplex Mode Setting SpecificationsModule Installation Refer to Console Telnet management chapter and Web management 3.4 Making Trunk Connections3. Only one trunk can exist between two switch units Rules2. One trunking port can only belong to one trunk 3.5 Making Sniffer Monitored PortsSniffer Port 4. LED Indicators 4.1 LED Panels4.2 Interpretation 5.1 Management Support 5. Performing Network ManagementLogin Port Status 5.2 Management objectsAdministrator Port Statistics5.3 Setting IP Address 5.4 Console ManagementFactory default settings of the Console port 5.6 Telnet Management 5.5 Web Managementhttp//xxx.xxx.xxx.xxx telnet5.8 Support 5.7 SNMP Management6. Console & Telnet Management Factory default Username admin Factory default PasswordThe main menu is shown as follows 6.2 IP Status 6.1 Set IP AddressThe port status definitions are 6.3 View Port StatusXmitAbort 6.4 View Port Counters6.5 View STP Status PathCostPriority Page 6.6 Restore Default Values Select 6 from main menu to restore factory default settingsFactory default settings are Console SFTP Utility 6.7 Update FirmwareThe steps are 6.8 Remote Boot System 7.1 Start Browser Software and Making Connection 7. Web ManagementLogin 7.2 Login to the Switch1. Home home page and device image 4. Administrator other management functions2. Port Status view all port status 3. Port Statistics view all port statistic counters7.3 Port Status 7.4 Port Statistics Click Administrator to perform more management functions as follows 7.5 AdministratorClick Basic to view or modify the following settings 7.5.1 BasicIP Address settings are IP AddressUse scroll bar to view all settings as follows SNMP EntriesThe SNMP settings are Click Advanced in menu to perform 7.5.2 AdvancedAdvanced / Spanning Page Page MAC Address Click Spanning to view and change Spanning tree protocol settingsPriority Path Cost Port NumberPort Status PriorityNone Advanced / TrunkingPort 1,2 Port 7,8Advanced / Sniffer Click Update to change sniffer port BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow Control 7.5.3 Console Port Information7.5.4 Port Controls Port Control - enable or disable port functionAuto - Auto-negotiation is enabled Click Security Manager to view or change user name and password 7.5.5 Security Manager7.5.6 System Manager TFTP Update Firmware Remote Boot SystemTFTP Update Firmware Page Remote Boot System