Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 operation manual 10/100 Fast Ethernet Managed Switch with Fiber Connectivity

Models: KS-801

1 63

Download 63 pages 48.76 Kb

Page 1

10/100 Fast Ethernet Managed Switch with Fiber Connectivity

KS-801

Operation Manual

DOC.020419-KS801-K

Image 1

Xerox KS-801 operation manual 10/100 Fast Ethernet Managed Switch with Fiber Connectivity, DOC.020419-KS801-K

Contents

DOC.020419-KS801-K 10/100 Fast Ethernet Managed Switch with Fiber ConnectivityCISPR A COMPLIANCE TRADEMARKSCE NOTICE 4. LED Indicators 2. Installing the Switch1. Introduction 3. Making Network Connections7. Web Management 6. Console & Telnet Management1. Introduction 1.1 Features TFTP - software upgrade capability Management FeaturesOut-of-band console management via RS232 console port In-band Telnet management over TCP/IP network1.2 Specifications 2.1 Packing List 2. Installing the SwitchCrossover setting switch for 10/100 Port #9 2.2 PanelsLED display for power and all port status Plug-in socket for AC power cordInstall Rack Mount Brackets 2.3 Mounting the SwitchesInstall the Switch into a 19-inch Rack Desktop Mounting3. Making Network Connections 3.1 Network Switched PortsMDI-X Jacks MDI Jack PIN#Crossover SW Port #9 RJ-45Manual Configuration 3.2 10/100BASE-TX Fast Ethernet PortsAuto-negotiation Capable Auto-speed-sensingUTP Cable Connections Flow ControlStraight-through and Crossover UTP Cable CONNECTED DEVICE3.3 Fast Ethernet Fiber Slot Fiber Jumper Setting Fiber Module Top view Fiber Jumper SettingModule Outline Specifications Duplex Mode SettingModule Installation Refer to Console Telnet management chapter and Web management 3.4 Making Trunk ConnectionsRules 3. Only one trunk can exist between two switch units2. One trunking port can only belong to one trunk Monitored Ports 3.5 Making SnifferSniffer Port 4.1 LED Panels 4. LED Indicators4.2 Interpretation 5.1 Management Support 5. Performing Network ManagementLogin Port Status 5.2 Management objectsAdministrator Port Statistics5.4 Console Management 5.3 Setting IP AddressFactory default settings of the Console port 5.6 Telnet Management 5.5 Web Managementhttp//xxx.xxx.xxx.xxx telnet5.8 Support 5.7 SNMP ManagementFactory default Username admin Factory default Password 6. Console & Telnet ManagementThe main menu is shown as follows 6.2 IP Status 6.1 Set IP AddressThe port status definitions are 6.3 View Port StatusXmitAbort 6.4 View Port CountersPathCost 6.5 View STP StatusPriority Page Select 6 from main menu to restore factory default settings 6.6 Restore Default ValuesFactory default settings are Console SFTP Utility 6.7 Update FirmwareThe steps are 6.8 Remote Boot System 7.1 Start Browser Software and Making Connection 7. Web ManagementLogin 7.2 Login to the Switch1. Home home page and device image 4. Administrator other management functions2. Port Status view all port status 3. Port Statistics view all port statistic counters7.3 Port Status 7.4 Port Statistics Click Administrator to perform more management functions as follows 7.5 AdministratorClick Basic to view or modify the following settings 7.5.1 BasicIP Address settings are IP AddressUse scroll bar to view all settings as follows SNMP EntriesThe SNMP settings are Click Advanced in menu to perform 7.5.2 AdvancedAdvanced / Spanning Page Page Click Spanning to view and change Spanning tree protocol settings MAC AddressPriority Path Cost Port NumberPort Status PriorityNone Advanced / TrunkingPort 1,2 Port 7,8Advanced / Sniffer Click Update to change sniffer port BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow Control 7.5.3 Console Port InformationPort Control - enable or disable port function 7.5.4 Port ControlsAuto - Auto-negotiation is enabled Click Security Manager to view or change user name and password 7.5.5 Security Manager7.5.6 System Manager TFTP Update Firmware Remote Boot SystemTFTP Update Firmware Page Remote Boot System