Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 operation manual SNMP Entries, Use scroll bar to view all settings as follows

Models: KS-801

1 63

Download 63 pages 48.76 Kb

Page 46

SNMP Entries

SNMP Entries

Use scroll bar to view all settings as follows:

-46-

Image 46

Xerox KS-801 operation manual SNMP Entries, Use scroll bar to view all settings as follows

Contents

10/100 Fast Ethernet Managed Switch with Fiber Connectivity DOC.020419-KS801-KCISPR A COMPLIANCE TRADEMARKSCE NOTICE 1. Introduction 2. Installing the Switch4. LED Indicators 3. Making Network Connections6. Console & Telnet Management 7. Web Management1. Introduction 1.1 Features Out-of-band console management via RS232 console port Management FeaturesTFTP - software upgrade capability In-band Telnet management over TCP/IP network1.2 Specifications 2. Installing the Switch 2.1 Packing ListLED display for power and all port status 2.2 PanelsCrossover setting switch for 10/100 Port #9 Plug-in socket for AC power cordInstall the Switch into a 19-inch Rack 2.3 Mounting the SwitchesInstall Rack Mount Brackets Desktop Mounting3.1 Network Switched Ports 3. Making Network ConnectionsCrossover SW PIN#MDI-X Jacks MDI Jack Port #9 RJ-45Auto-negotiation Capable 3.2 10/100BASE-TX Fast Ethernet PortsManual Configuration Auto-speed-sensingStraight-through and Crossover UTP Cable Flow ControlUTP Cable Connections CONNECTED DEVICE3.3 Fast Ethernet Fiber Slot Fiber Jumper Setting Fiber Module Top view Fiber Jumper SettingModule Outline Specifications Duplex Mode SettingModule Installation 3.4 Making Trunk Connections Refer to Console Telnet management chapter and Web managementRules 3. Only one trunk can exist between two switch units2. One trunking port can only belong to one trunk Monitored Ports 3.5 Making SnifferSniffer Port 4.1 LED Panels 4. LED Indicators4.2 Interpretation 5. Performing Network Management 5.1 Management SupportAdministrator 5.2 Management objectsLogin Port Status Port Statistics5.4 Console Management 5.3 Setting IP AddressFactory default settings of the Console port http//xxx.xxx.xxx.xxx 5.5 Web Management5.6 Telnet Management telnet5.7 SNMP Management 5.8 SupportFactory default Username admin Factory default Password 6. Console & Telnet ManagementThe main menu is shown as follows 6.1 Set IP Address 6.2 IP Status6.3 View Port Status The port status definitions are6.4 View Port Counters XmitAbortPathCost 6.5 View STP StatusPriority Page Select 6 from main menu to restore factory default settings 6.6 Restore Default ValuesFactory default settings are 6.7 Update Firmware Console SFTP UtilityThe steps are 6.8 Remote Boot System 7. Web Management 7.1 Start Browser Software and Making Connection7.2 Login to the Switch Login2. Port Status view all port status 4. Administrator other management functions1. Home home page and device image 3. Port Statistics view all port statistic counters7.3 Port Status 7.4 Port Statistics 7.5 Administrator Click Administrator to perform more management functions as follows7.5.1 Basic Click Basic to view or modify the following settingsIP Address IP Address settings areSNMP Entries Use scroll bar to view all settings as followsThe SNMP settings are 7.5.2 Advanced Click Advanced in menu to performAdvanced / Spanning Page Page Click Spanning to view and change Spanning tree protocol settings MAC AddressPriority Port Status Port NumberPath Cost PriorityPort 1,2 Advanced / TrunkingNone Port 7,8Advanced / Sniffer Click Update to change sniffer port 7.5.3 Console Port Information BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow ControlPort Control - enable or disable port function 7.5.4 Port ControlsAuto - Auto-negotiation is enabled 7.5.5 Security Manager Click Security Manager to view or change user name and passwordTFTP Update Firmware Remote Boot System 7.5.6 System ManagerTFTP Update Firmware Page Remote Boot System