Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 operation manual Fast Ethernet Fiber Slot

Models: KS-801

1 63

Page 16

3.3 Fast Ethernet Fiber Slot

The switch provides one fast Ethernet fiber slot. It can accommodate one optional fiber module for your fiber connection. Depending on the fiber interface and the types of fiber cables, the following fiber modules are available for selection:

Module	Connector type	Fiber cable	Maximum length
800-T	ST	MM*	2	Km
800-C	SC	MM	2	Km
800-SA	SC	SM *	15	Km
800-S3	SC	SM	30	Km
800-S5	SC	SM	50	Km
800-JM	MT-RJ	MM	2	Km
800-JS	MT-RJ	SM	15	Km
800-VM	VF-45	MM	2	Km

*MM : Multimode fiber cable, SM : Single mode fiber cable

Switched port #9 supports two types of connections. One type is UTP connection through Port 9X. The other is fiber connection through slot FIBER respectively. Both types of connections can not be used at the same time. Each fiber module provides optional jumpers to enable or disable fiber connection.

-16-

Page 16

Image 16

Xerox KS-801 operation manual Fast Ethernet Fiber Slot

Contents

10/100 Fast Ethernet Managed Switch with Fiber Connectivity DOC.020419-KS801-KCISPR A COMPLIANCE TRADEMARKSCE NOTICE 2. Installing the Switch 4. LED Indicators1. Introduction 3. Making Network Connections6. Console & Telnet Management 7. Web Management1. Introduction 1.1 Features Management Features TFTP - software upgrade capabilityOut-of-band console management via RS232 console port In-band Telnet management over TCP/IP network1.2 Specifications 2. Installing the Switch 2.1 Packing List2.2 Panels Crossover setting switch for 10/100 Port #9LED display for power and all port status Plug-in socket for AC power cord2.3 Mounting the Switches Install Rack Mount BracketsInstall the Switch into a 19-inch Rack Desktop Mounting3.1 Network Switched Ports 3. Making Network ConnectionsPIN# MDI-X Jacks MDI JackCrossover SW Port #9 RJ-453.2 10/100BASE-TX Fast Ethernet Ports Manual ConfigurationAuto-negotiation Capable Auto-speed-sensingFlow Control UTP Cable ConnectionsStraight-through and Crossover UTP Cable CONNECTED DEVICE3.3 Fast Ethernet Fiber Slot Fiber Jumper Setting Fiber Module Top view Fiber Jumper SettingModule Outline Specifications Duplex Mode SettingModule Installation 3.4 Making Trunk Connections Refer to Console Telnet management chapter and Web managementRules 3. Only one trunk can exist between two switch units2. One trunking port can only belong to one trunk Monitored Ports 3.5 Making SnifferSniffer Port 4.1 LED Panels 4. LED Indicators4.2 Interpretation 5. Performing Network Management 5.1 Management Support5.2 Management objects Login Port StatusAdministrator Port Statistics5.4 Console Management 5.3 Setting IP AddressFactory default settings of the Console port 5.5 Web Management 5.6 Telnet Managementhttp//xxx.xxx.xxx.xxx telnet5.7 SNMP Management 5.8 SupportFactory default Username admin Factory default Password 6. Console & Telnet ManagementThe main menu is shown as follows 6.1 Set IP Address 6.2 IP Status6.3 View Port Status The port status definitions are6.4 View Port Counters XmitAbortPathCost 6.5 View STP StatusPriority Page Select 6 from main menu to restore factory default settings 6.6 Restore Default ValuesFactory default settings are 6.7 Update Firmware Console SFTP UtilityThe steps are 6.8 Remote Boot System 7. Web Management 7.1 Start Browser Software and Making Connection7.2 Login to the Switch Login4. Administrator other management functions 1. Home home page and device image2. Port Status view all port status 3. Port Statistics view all port statistic counters7.3 Port Status 7.4 Port Statistics 7.5 Administrator Click Administrator to perform more management functions as follows7.5.1 Basic Click Basic to view or modify the following settingsIP Address IP Address settings areSNMP Entries Use scroll bar to view all settings as followsThe SNMP settings are 7.5.2 Advanced Click Advanced in menu to performAdvanced / Spanning Page Page Click Spanning to view and change Spanning tree protocol settings MAC AddressPriority Port Number Path CostPort Status PriorityAdvanced / Trunking NonePort 1,2 Port 7,8Advanced / Sniffer Click Update to change sniffer port 7.5.3 Console Port Information BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow ControlPort Control - enable or disable port function 7.5.4 Port ControlsAuto - Auto-negotiation is enabled 7.5.5 Security Manager Click Security Manager to view or change user name and passwordTFTP Update Firmware Remote Boot System 7.5.6 System ManagerTFTP Update Firmware Page Remote Boot System