Specifications | Xerox KS-801 specs

1.2 Specifications

Standard	IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX FX
	IEEE 802.3x Full duplex flow control
	IEEE 802.1D Spanning tree
Network ports	9 10/100BASE-TX switched ports
	1 Fast Ethernet fiber slot for 100BASE-FX fiber modules
Console port	1 DB9 Male connector
Cables	10BASE-T Cat. 3, 4, 5 UTP cable (100 meters max.)
	100BASE-TX Cat. 5 UTP cable (100 meters max.)
	100BASE-FX Multimode and Single Mode fiber
UnitLED	Power status
TP Port LED	Link/Activity, Speed, Duplex/Collision status per port
Filtering rate	14,880 pps for Ethernet (10BASE-T)

148.8Kpps for Fast Ethernet (100BASE-TX and -FX)

Forwardingrate 14,880 pps for Ethernet (10BASE-T)

148.8Kpps for Fast Ethernet (100BASE-TX and -FX)

Filtering address Multicast/Broadcast/Unicast address MAC addresses 4K entries

Trunking	2 trunks max., 4 trunking ports per trunk max.
RAM buffer	512K bytes
Environment	Temperature	0oC to 40oC
	Relative humidity	10% to 90% non-condensing
Power	Universal power supply 100-240VAC, 47-63Hz, 25W
Dimension	260x150x44.4mm (10.24x5.9x1.75inch)

-8-

Image 8

Xerox KS-801 operation manual Specifications

Contents

10/100 Fast Ethernet Managed Switch with Fiber Connectivity Trademarks Table of Contents Console & Telnet Management Web Management Introduction Features Page Specifications Installing the Switch Packing List Panels Mounting the Switches Install Rack Mount BracketsInstall the Switch into a 19-inch Rack Desktop Mounting Network Switched Ports Making Network Connections 10/100BASE-TX Fast Ethernet Switched Ports MDI-X and MDI RJ-45 Connectors Manual Configuration 10/100BASE-TX Fast Ethernet PortsAuto-negotiation Capable Auto-speed-sensing Straight-through and Crossover UTP Cable Flow ControlUTP Cable Connections Module Connector type Fiber cable Maximum length Fast Ethernet Fiber Slot Fiber Module Top view Fiber Jumper Setting Module Outline Module Installation Duplex Mode SettingSpecifications Switch supports the following trunk configurations Making Trunk ConnectionsPage When doing sniffer, configure Making SnifferMonitored Ports Sniffer Port Interpretation LED IndicatorsLED Panels Performing Network Management Management Support Login Port Status Management objects Setting IP Address Console Management Refer to for more information Telnet ManagementConsole port does not support modem connection Snmp Management Support Console & Telnet Management Set IP Address IP StatusSelect 1 from main menu to set IP address Select 2 from main menu to view IP status View Port Status Port status definitions are View Port Counters View STP Status Page Restore Default Values Update Firmware Console Sftp Utility Prompts shown on DOS screen are as follows \WINDOWSSFTP Remote Boot System Processing messages shown on console screen are Set IP Address for the Switch Web ManagementStart Browser Software and Making Connection Web Browser Factory default Username Admin Factory default Password Login to the SwitchLogin Page Port Status Port Statistics Administrator Click Basic to view or modify the following settings Basic IP Address settings are IP Address Use scroll bar to view all settings as follows Snmp Entries Snmp settings are Advanced Click Advanced in menu to perform Advanced / Spanning Page Page Priority is assigned to the switch. The higher MAC address of the switch as a unique identiValue is lower priority. Range 0 Fier to the network Ports which are enabled can be in one of the follow Listening Switches send messages to one anotherBlocking The switch enters the Blocking State if a Learning The switch enters the Learning State if no Advanced / Trunking Advanced / Sniffer Page Console Port Information Port Controls Security Manager System Manager Click System Manager to perform Tftp Update Firmware Click Apply to start Tftp file transfer operationsPage Remote Boot System