Manuals / Xerox / Computer Equipment / Switch

Xerox KS-801 operation manual Duplex Mode Setting, Specifications, Module Installation

Models: KS-801

1 63

Page 18

Duplex Mode Setting

The duplex mode used for the fiber module is configured by software port control settings. See chapter 5 for more information.

Specifications

Standard	IEEE 802.3u 100BASE-FX
Speed	100Mbps
Duplex mode	Full duplex or half duplex
Wavelength	1300nm
Fiber Connectors	ST, SC, MT-RJ, VF-45
Fiber cable	MM 50/125mm, 62.5/125mm recommended
	SM 9/125mm recommended

Module Installation

1.Turn off the power to the switch unit.

2.Open the cover of Fiber slot.

3.Set Fiber jumper J1.

4.Insert the module into slot until it is seated properly.

5. Screw the module onto the chassis securely.

-18-

Page 18

Image 18

Xerox KS-801 operation manual Duplex Mode Setting, Specifications, Module Installation

Contents

10/100 Fast Ethernet Managed Switch with Fiber Connectivity DOC.020419-KS801-KTRADEMARKS CISPR A COMPLIANCECE NOTICE 1. Introduction 2. Installing the Switch4. LED Indicators 3. Making Network Connections6. Console & Telnet Management 7. Web Management1. Introduction 1.1 Features Out-of-band console management via RS232 console port Management FeaturesTFTP - software upgrade capability In-band Telnet management over TCP/IP network1.2 Specifications 2. Installing the Switch 2.1 Packing ListLED display for power and all port status 2.2 PanelsCrossover setting switch for 10/100 Port #9 Plug-in socket for AC power cordInstall the Switch into a 19-inch Rack 2.3 Mounting the SwitchesInstall Rack Mount Brackets Desktop Mounting3.1 Network Switched Ports 3. Making Network ConnectionsCrossover SW PIN#MDI-X Jacks MDI Jack Port #9 RJ-45Auto-negotiation Capable 3.2 10/100BASE-TX Fast Ethernet PortsManual Configuration Auto-speed-sensingStraight-through and Crossover UTP Cable Flow ControlUTP Cable Connections CONNECTED DEVICE3.3 Fast Ethernet Fiber Slot Fiber Module Top view Fiber Jumper Setting Fiber Jumper SettingModule Outline Duplex Mode Setting SpecificationsModule Installation 3.4 Making Trunk Connections Refer to Console Telnet management chapter and Web management3. Only one trunk can exist between two switch units Rules2. One trunking port can only belong to one trunk 3.5 Making Sniffer Monitored PortsSniffer Port 4. LED Indicators 4.1 LED Panels4.2 Interpretation 5. Performing Network Management 5.1 Management SupportAdministrator 5.2 Management objectsLogin Port Status Port Statistics5.3 Setting IP Address 5.4 Console ManagementFactory default settings of the Console port http//xxx.xxx.xxx.xxx 5.5 Web Management5.6 Telnet Management telnet5.7 SNMP Management 5.8 Support6. Console & Telnet Management Factory default Username admin Factory default PasswordThe main menu is shown as follows 6.1 Set IP Address 6.2 IP Status6.3 View Port Status The port status definitions are6.4 View Port Counters XmitAbort6.5 View STP Status PathCostPriority Page 6.6 Restore Default Values Select 6 from main menu to restore factory default settingsFactory default settings are 6.7 Update Firmware Console SFTP UtilityThe steps are 6.8 Remote Boot System 7. Web Management 7.1 Start Browser Software and Making Connection7.2 Login to the Switch Login2. Port Status view all port status 4. Administrator other management functions1. Home home page and device image 3. Port Statistics view all port statistic counters7.3 Port Status 7.4 Port Statistics 7.5 Administrator Click Administrator to perform more management functions as follows7.5.1 Basic Click Basic to view or modify the following settingsIP Address IP Address settings areSNMP Entries Use scroll bar to view all settings as followsThe SNMP settings are 7.5.2 Advanced Click Advanced in menu to performAdvanced / Spanning Page Page MAC Address Click Spanning to view and change Spanning tree protocol settingsPriority Port Status Port NumberPath Cost PriorityPort 1,2 Advanced / TrunkingNone Port 7,8Advanced / Sniffer Click Update to change sniffer port 7.5.3 Console Port Information BaudRate Bit/sec Data Bits Parity Check Stop Bits Flow Control7.5.4 Port Controls Port Control - enable or disable port functionAuto - Auto-negotiation is enabled 7.5.5 Security Manager Click Security Manager to view or change user name and passwordTFTP Update Firmware Remote Boot System 7.5.6 System ManagerTFTP Update Firmware Page Remote Boot System