Yamaha DSP5D, PM5D-RH V2 Main area of the display, Lower part of the display (always visible)

Main area of the display

164 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

• PRESENT TIME

Indicates the present time. The time can be specified in

the UTILITY function PREFERENCE 1 screen.

• TIME CODE

Indicates the internal time code being generated by the

PM5D (machine #1), or the time code being received

from an external device. This is the same as the time

code shown in the SCENE function EVENT LIST

screen.

• CASCADE/Fs

Indicates the master/slave status when using a cascade

connection, and the sampling frequency at which the

PM5D system is currently operating.

EMETER SECTION

Indicates the type of channels that are currently shown

by the meters in the upper left and right of the panel.

You can also click the / buttons to switch this

directly.

FEVENT indicator

The EVENT indicator is displayed here if the ENABLE

[ALL MANUAL] or ENABLE button is turned on in

the SCENE function EVENT LIST screen.

GFADING/TRACKING indicator

This area shows the FADING indicator while fade time

is being executed, or the TRACKING indicator if

Tracking Recall is available. If both are enabled, FAD-

ING takes priority.

HLCR/LCR [B] indicator

If there is at least one channel for which LCR is turned

on, the LCR indicator is displayed here.

If in the SYS/W.CLOCK function MIXER SETUP

screen the BUS SETUP setting STEREO B is set to USE

AS CENTER BUS, the LCR [B] indicator is displayed

here.

ITB/OSC/DIMM indicator

If talkback, oscillator, or dimmer are on, the respective

TB/OSC/DIMM indicator is displayed here. If more

than one of these are enabled, the display priority is

TB>OSC>DIMM.

JSOLO/INPUT CUE/DCA CUE/OUTPUT CUE/

KEY IN CUE/EFFECT CUE/EXTERNAL CUE

indicator

If Solo or Cue Monitor is enabled, the corresponding

indicator is shown here. If more than one Cue is

selected, only the indicator for the currently-valid Cue

is shown.

KBUSY/RS422/HA/GPI/MIDI indicator

The BUSY indicator is shown here while internal mem-

ory or a PC card in the card slot is being accessed.

When RS422/HA/GPI/MIDI signals are received (in

the case of RS422, when Status is received to indicate a

status change on a connected device), the appropriate

indicator will appear briefly. If more than one of these

conditions occur simultaneously, the display priority is

BUSY>RS422>HA>GPI>MIDI.

Note

In the case of MIDI signals, the indicator will light if signals are

received at the MIDI connector, USB connector, or slots 1–4.

However, active sensing, MIDI clock, and quarter time code

messages will not cause the indicator to light.

Main area of the display

ATabs

Click this area to switch between screens within the

selected function.

BFunction parameters

This area shows parameters for the currently selected

function or screen.

Lower part of the display (always visible)

ASELECTED CH (Selected channel)

Indicates the type and name of the channel currently

selected by the [SEL] key. You can also move the cur-

sor and turn the [DATA] encoder to change this

directly.

BMACHINE ID

If the DSP5 is cascade-connected, this indicates the

machine (PM5D or DSP5D) #1–#3 that is being con-

trolled from the panel. You can also move the cursor

and turn the [DATA] encoder to change this directly.

When you switch machines, the screen background

color and the constantly displayed screen (except for

time code) will also change to the settings of the

machine that is now being controlled. The screen back-

ground color can be specified for each machine in the

UTILITY function PREFERENCE 2 screen. The indica-

tor above will light only for the machine ID number

that is cascade-connected.

CMIX SECTION

Indicates the encoder mode currently selected in the

MIX section. In MIX SEND mode this indicates

“SEND,” in MIX MASTER mode this indicates “MAS-

TER,” and if a shortcut operation has been used to

select TO MATRIX mode this indicates “TO

MATRIX.” You can also move the cursor and turn the