Yamaha DSP5D, PM5D-RH V2 TRACKING RECALL screen

SCENE function

186 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can make settings for the Tracking Recall func-

tion, which adds a specified offset value to the value of each

fader when you recall a scene.

ATRACKING RECALL ENABLED/DISABLED

Enables/disables the Tracking Recall function.

Hint

The settings in the TRACKING RECALL screen apply to all

scenes.

BDISPLAY SELECT

These buttons select the type of channels that are

shown in the TRACKING RECALL screen; either

INPUT (input channels) or OUTPUT (output

channels).

CSET ALL

This button enables Tracking Recall for all channels

(including channels not currently shown in the screen).

DCLEAR ALL

This button disables Tracking Recall for all channels

(including channels not currently shown in the screen).

EOFFSET LOCK

If this button is on, the sliders of all channels (includ-

ing channels not currently shown in the screen) will be

grayed-out, and you will be unable to edit the offset

value.

FON (Tracking On)

These buttons enable/disable tracking for each chan-

nel. If the TRACKING RECALL ENABLED/

DISABLED button is set to ENABLED, tracking is

enabled on channels for which this button is ON.

Note

If OFFSET LOCK (

5

) is off, turning this button on will reset

the tracking offset of the corresponding channel to 0 dB. If in

this state you operate the fader of the corresponding channel,

the relative amount of fader movement from the point at which

this button was turned on will be memorized as the tracking

offset. You can then turn OFFSET LOCK on to lock the offset.

This offset value will be added whenever you subsequently

recall a scene.

GTracking offset

Here you can specify the offset value applied to each

channel if tracking is enabled. The range is ±15 dB.

While OFFSET LOCK (5) is off, operating the panel

faders will cause these values to change as well; how-

ever, adjusting the offset values in the screen will not

cause the panel faders to move.

TRACKING RECALL screen

TRACKING RECALL

34

21 5

7

6

Contents

Main PM5D/PM5D-RH V2 DSP5D Owners Manual Owners Manual Owners Manual PM5D/PM5D-RH V2 / DSP5D IMPORTANT SAFETY INSTRUCTIONS CAUTION 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) ADVARSEL! Connecting the Plug and Cord IMPORTANT NOTICE FOR THE UNITED KINGDOM 1/2 Location PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING CAUTION WARNING Included Accessories Connections 2/2 PM5D/PM5D-RH V2 / DSP5D Owners Manual Table of Contents Operating section Input Patch / Output Patch operations. 74 Using the Selected Channel section.....65 Output channel operations ..................55 Connections and setup........................ 31 Grouping and linking............................81 Other functions................................148 Surround pan...................................142 Using memory cards........................138 Graphic EQ and Parametric EQ....... 118 PM5D/PM5D-RH V2 / DSP5D Owners Manual Table of Contents Reference section Information shown in the display.......... 163 Output functions.................................... 243 PM5D/PM5D-RH V2 / DSP5D Owners Manual Table of Contents 9 Input functions........................................277 Scene Memory/Effect Library to Program Change Table Appendices..............................................317 Operating section 1Introduction Thank you An overview of the PM5D system Full digital SR mixing system Differences between the PM5D model and the PM5D-RH model PM5D model PM5D-RH model 1 Input channels About the DSP5D Connectors and interfaces not found on the DSP5D Connectors and interfaces found only the DSP5D About the channel structure of the Connection to a computer About PM5D Editor and DSP5D Editor Regarding cascade connections between the PM5D and DSP5D 1 Firmware versions Major new functionality in PM5D rmware V2.0 Basic functionality and panel operations EFFECT functions GEQ functions Regarding word clock synchronization Conventions in this manual How this manual is organized Operating section Reference section 2Top, front, and rear panels 4 5 3 6 8 7 R 9 Q R ST N O P 8 J K M L Rear panel Top, front, and rear panels GMIX OUT jacks HLAMP connector IMONITOR OUT jacks JCUE OUT jacks Front panel DSP5D front panel DSP5D rear panel This chapter explains the various types of user interface used to operate the PM5D. About the various types of user interface Pointer Cursor 3Basic operation on the PM5D User interface in the display Scroll bar DISPLAY ACCESS section Data Entry section FTrack pad and left/right buttons GPHONES (Headphone) jack Mouse Numeric key pad Keyboard Full keyboard External user interface Basic operation Click Drag and drop Drag Using the keys of the DISPLAY ACCESS section 1 2 Using buttons within the display 1 2 3 1 Accessing a desired screen Moving the cursor 2 Scrolling the screen 1 2 3 Operating the buttons Adjusting the setting of a knob or fader 1 2 3 Assigning a name Examples of systems expanded with the DSP5D 4Connections and setup FoH Example of simple input expansion (PM5D + one DSP5D unit) FoH PM5D + remotely connected input expansion (PM5D + DCU5D + two DSP5D units) Page Audio connections Analog audio connections Analog output connections Page Digital input/output connections DAT 1 2 3 4 Installing an option card Word clock connections and settings Using daisy-chain connections Using a word clock distribution box About word clock Selecting the word clock master 2 3 Restoring the current scene to the default state 1 2 Switching the target of panel operations (when cascade-con- nected with the DSP5D) 1 5Input channel operations FX RTN channels 14 AD IN section Items in the AD IN section A[+48V ON/OFF] LED B[PEAK]/[SIGNAL] LED C[LAMP DIMMER] knob 1 2 3 A+48V button BGAIN knob INPUT channel strip Items in the INPUT channel strip Page ST IN/FX RTN channel strip Items in the ST IN/FX RTN channel strip FADER FLIP/ENCODER MODE section Items in the FADER FLIP/ENCODER MODE section Various operations for input channels Selecting the function of the encoders Exchanging the fader and encoder 1 2 3 4 5 1 2 3 4 To send signals from a specic input chan- nel to all MIX buses 1 2 3 Sending the signal from the input channel to a MIX bus 4 a FIXED type MIX bus INPUT CHANNEL 1 INPUT CHANNEL 2 a VARI type MIX bus 1 2 Using vertical pairing 1 2 3 Enabling/disabling pairing 4 5 6 This chapter explains the functions and operation of each section related to output channels. About the output channels 6Output channel operations MATRIX channels 18 MIX section A[TO ST] LED B[TO MTRX] LED CDCA group LEDs DMIX [PAIR] LED 1 2 3 4 5 1 2 3 4 5 Sending signals from MIX channels to the STEREO bus 1 2 3 5 6 7 8 Pairing MIX channels Signals sent from an input channel to a VARI type MIX bus MIX channel output signals STEREO A/B channel strip Items in the STEREO A/B channel strip Sending signals from the STEREO A/B channels to output jacks 1 2 3 Sending signals from the STEREO A/B channels to MATRIX buses 1 2 3 4 5 MATRIX section ADCA group LEDs Operations in the MATRIX section BMATRIX [PAIR] LED CMATRIX [ON] key Signals sent from MIX channels and STE- REO A/B channels to MATRIX buses Output signals from MATRIX channels About the SELECTED CHANNEL section Items in the SELECTED CHANNEL section Using the Selected Channel section GROUP CHANNEL SELECT DELAY GAIN/ATTENUATION/ (Gain / Attenuation / Phase) NOISE GATE STEREO COMPRESSOR Input channels Output channels HPF (High Pass Filter) EQUALIZER EEQ [Q] encoder Operations in the SELECTED CHANNEL section 1 2 3 Selecting a channel and editing its parameters 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 8Input Patch / Output Patch operations 4 5 Changing the output patch settings 1 2 3 4 5 Inserting an external device into a channel Insert connection example Connecting an external device for insertion 1 2 3 4 Patching the insert-out and insert-in 5 6 Directly outputting the signal of an input channel 1 2 3 4 9Grouping and linking FDCA [CUE] key Using DCA Groups To select the DCA groups to which a specic channel will belong 1 2 3 Using mute groups To select the mute groups to which a specic channel will belong 1 2 3 1 Using the Mute Safe function Controlling mute groups 2 3 1 2 3 1 2 3 Grouping and linking Using EQ Link and Compressor Link 2 3 4 This chapter explains how to store and recall the PM5Ds mix parameters as scenes. About scenes 10 Scene memory Items in the SCENE MEMORY section Using scene memories 1 2 3 4 Using PREVIEW mode 1 2 3 4 Using the Auto Store function 1 2 Using the Direct Recall function 1 Using the Selective Recall function 1 2 3 Input channels / Output channels 4 5 Using the Recall Safe function 1 2 3 Using the Fade function 1 2 3 4 Using the Tracking Recall function 1 2 3 4 Using the Global Paste function 1 2 3 4 5 This chapter explains the PM5Ds Monitor and Cue functions. About the MONITOR and CUE sections 11 Monitor and Cue Using the Monitor function Items in the MONITOR section 1 2 3 4 5 Using the Cue/Solo functions About CUE mode and SOLO mode A[INPUT]/[DCA]/[OUTPUT] LEDs B[SOLO] key C[LAST CUE] key Cue and Solo groups 1 2 3 Using the Solo function 4 1 2 3 4 Using the Cue function 12 Talkback and Oscillator Items in the TALKBACK/OSCILLATOR sections 12 Using talkback 1 2 3 4 Using the oscillator 1 2 3 4 13 Meters 1L 1R 2L 2R 3L 3R 4L 4R MATRIX ST IN/ / 32 54 Key [INPUT/MIX] meters Switching the metering point 1 2 1 2 Viewing the gain reduction of the internal gates and compres- sors 1 2 Viewing the gain reduction for input channels Viewing the gain reduction for out- put channels 14 Effects Using an internal effect via a MIX bus 1 2 3 4 Inserting an internal effect into a channel 1 2 3 4 Basic operations in the effect screen 1 2 3 4 1 2 3 1 2 3 Editing the effect parameters Storing settings in the effect library Using the Tap Tempo function 1 2 3 Using the Freeze effect 1 2 3 4 15 Graphic EQ and Parametric EQ Graphic EQ and Parametric Expanding the GEQ modules 1 2 Basic graphic EQ operations 1 2 3 4 5 1 2 3 4 5 Controlling the graphic EQ from the DCA section Basic parametric EQ operations 1 2 3 4 1 2 3 4 5 16 Remote control 3 4 5 6 7 Using control changes to control events 1 2 3 4 5 6 7 Using the MIDI Remote function 1 2 Assigning MIDI messages to controllers 3 4 5 6 7 BSpecifying the type of message CUsing the LEARN button 8 1 2 3 4 5 Transmitting MIDI events when you switch scenes 1 2 3 4 Using GPI (General Purpose Interface) 1 2 3 Using GPI IN 4 click the button to open the GPI IN PORT ASSIGN window. After you have specified the function and parameter, click the OK button. 5 1 2 3 4 5 6 7 1 2 3 4 FADER START 5 17 This chapter explains how to save/load PM5D/DSP5D internal data using a memory card. Using memory cards with the PM5D Saving les to a memory card 17 Using memory cards Using memory cards 5 6 7 8 17 Loading les from a memory card 1 2 3 4 6 7 8 9 This chapter explains how to use the surround pan functionality. 18 Surround pan Bus conguration and operation in surround mode If the MIX section [MIX SEND] key is on 1 2 3 4 5 AL R BF R Basic settings for surround buses 1 2 3 4 Controlling surround pan 1 2 3 4 5 6 Notes regarding surround pan Scene recall operations Channel library recall operations Channel copy Global paste 19 Other functions Items in the USER DEFINED section Assigning functions to the User Dened keys 5 1 Using the FADER MODE section AFADER MODE [A][F] keys BFADER MODE [DCA] key 1 Executing functions assigned to the User Dened keys 2 3 4 5 6 2 Switching the FADER MODE section layer Locking the PM5D (Security functions) 1 2 3 4 1 2 3 4 5 Using cascade connections Making settings on the DSP5D itself 1 2 Example of cascade connections between the PM5D and DSP5D 3 Making settings from DSP5D Editor 1 2 Cascade-connecting the PM5D and 3 Basic settings for cascade connection Cascade master (bi-directional cascade connections between PM5D units) 1 2 3 4 5 1 2 3 4 5 1 2 Selecting the buses used for cascade connection 3 4 5 Connecting the PM5D to your computer via USB 1 2 3 Caution when using the USB TO HOST connector Connecting the DSP5D to your computer via Ethernet 1 2 AIP ADDRESS BGATEWAY ADDRESS Initializing the PM5Ds internal memory 1 2 3 Initializing the DSP5Ds internal memory Adjusting the faders and input/output gain (Calibration) 1 Calibrating the faders 2 3 Adjusting the analog input gain (PM5D-RH model only) Adjusting the output gain Reference section 4 5 6 7 8 9 J K Upper part of the display (always visible) AFunction Name Indication Main area of the display ATabs BFunction parameters Lower part of the display (always visible) ASELECTED CH (Selected channel) Function menu EFFECT functions AEffect selection BEffect type CInput patch Global functions EFFECT PARAM (Effect parameter) 2 3 4 EMIX BALANCE FBYPASS K L J8 9 GCUE EFFECT ASSIGN screen Function Global Output Input EFFECT LIBRARY screen GEQ function AModule select 1 5 6 72 43 BLINK button PLUG-IN screen Function Global 8 9 Output Input When parametric EQ is selected Page GEQ LIBRARY screen Function Global 9 K Output SCENE function AScene list This is a list of the stored scenes. For each scene, the fol- lowing items are displayed. (To view COMMENT and subsequent items, scroll the list to the right.) B (Scene number) JTX ON/OFF (MIDI event transmission on/ off) KDELAY L M LGPI OUT CONTROL 112 MREMOTE TRANSPORT Function Global Output Input OBLANK SKIP BEvent list CEVENT RECALL P Q DAUTO CAPTURE EMOVE UP FMOVE DOWN GMANUAL INSERT HMANUAL OVERWRITE ITIME CODE SETUP SELECTIVE RECALL screen Page ASAFE KEY MODE SELECT (Safe Key Mode selection) BOUTPUT ISOLATION RECALL SAFE screen Page AFADING ENABLED/DISABLED BINPUT CH PANNING ENABLED/DISABLED (Input channel panning enable/disable) 1 2 3 CFADE TIME/START OFFSET FADE TIME screen Page TRACKING RECALL screen Function Global Output Input APASTE MODE MIDI REMOTE function AMODE MIDI SETUP screen BTx (MIDI transmission) CRx (MIDI reception) DECHO (MIDI message echo output) MIDI PGM CHANGE (MIDI program change) screen Function Global 564 Output Input MIDI REMOTE screen DBANK SELECT ECLEAR BANK FMIDI message GLEARN HLATCH GPI screen Function Global Output Input GPI IN MONITOR FADER START screen DCLEAR ALL AMMC DEVICE No. BRS422 DATA FORMAT CTransport TRANSPORT screen 5 64 Function Global 541 2 3 Output Input Connecting the PM5D with a DME series unit 1 2 Function Global Output Input 3 1 2 3 ACONNECT BMIDI PGM CHANGE (MIDI program change) CINPUT PORT 6 7 8 Controlling DME parameters 1 UTILITY function ASTORE/RECALL BPATCH CGATE/COMP (Gate / Compressor) PREFERENCE 1/2 screens DDCA MUTE TARGET EMETER SECTION FPANEL OPERATION PREFERENCE screen 2 GBRIGHTNESS HTRACK PAD/MOUSE ISCREEN TIPS JUPPER PART DISPLAY KNAME DISPLAY ([NAME] indicator display) Q R S LWARNING DISPLAY MCHANNEL NAME NUMERIC DISPLAY USER DEFINE screen Page UTILITY function Function Global Output Input AMODE ADVANCED mode DCATEGORY ESOURCE (save-source numbers) FDESTINATION (save-destination number) CSV EXPORT mode GLIBRARY TITLE HCHANNEL NAME P Q R N ISET ALL LK JCLEAR ALL 214 NNumber of files / Free area OSAVE PRENAME Function Global Output Input AFILE PATH ADVANCED mode GCATEGORY HSOURCE (load-source) IDESTINATION (load-destination) CSV IMPORT mode Function Global Output Input AMACHINE ID SECURITY screen Function Global Output Input SYS/W.CLOCK function AMASTER CLOCK SELECT WORD CLOCK screen BFs (Sampling frequency) CSlot number / Card type DINPUT FORMAT (Input signal format) EOUTPUT FORMAT (Output signal format) FFREQUENCY (Sampling frequency) GSRC (Sampling Rate Converter) Function Global Output Input A+48V MASTER (DSP5D only) EBUS SETUP FSTEREO B 587 GSURROUND BUS ALLOCATION HSURROUND MODE ITYPE SELECT L Q JCASCADE ENABLED/DISABLED KDME CONTROL M O K LCASCADE FROM (Source when cascade- connected) MCASCADE IN PORT SELECT NCASCADE TO (Transmission destination when cascade-connected) OCASCADE OUT PORT SOURCE SELECT PCASCADE MODE QBI-DIRECTION (Bi-directional communication) ACASCADE ENABLED/DISABLED CASCADE screen CCASCADE IN SOURCE (Cascade IN source I/ O assignment view) 43 5 6 DCASCADE IN ON/OFF EPARAM LINK (parameter link) FCASCADE OUT ON/OFF HA (Head Amp) screen Page Page METER function OUTPUT METER screen Page MON/CUE function OUTPUT GR (Output Gain Reduction) TALKBACK screen Page OSCILLATOR screen Function Global Output Input 2TR I/O screen MONITOR screen If the USE AS STEREO BUS button is on If the USE AS CENTER BUS button is on 3 4 BDEFINE CDIMMER CUE/SOLO screen CCUE FUNCTION DINPUT 4 5 6 EDCA FOUTPUT Page Function Global Output Input Output functions OUTPUT PATCH screen 34 Page Function Global Output Input DASSIGN INSERT POINT screen Page OUTPUT INSERT function INSERT IN MIX 1-24 screen INSERT IN MATRIX/STEREO/MONI- TOR screen A+48V BHPF (High Pass Filter) CCutoff frequency DGAIN EInput port OUTPUT EQ function EQ PARAM (EQ Parameter) screen Page OUTPUT EQ LIBRARY screen Function Global Output Input OUTPUT COMP function COMP PARAM (Compressor parame- ter) screen ELevel meters FType 6 97 8 GSTEREO LINK Key-in signal flow when Link= On Page COMP LIBRARY (Compressor library) Function Global Output Input OUTPUT DELAY function MIX 1-24 screen MATRIX/STEREO screen BGANG CDelay time knob 213 OUTPUT DCA/GROUP func- tion ADCA group BName DCA GROUP ASSIGN screen Function Global 321 Output Input EQ LINK ASSIGN screen Page CSET BY CUE (Assign by [CUE] key) DCLEAR MATRIX/ST function 43 AMATRIX bus BSend level MATRIX/ST ROUTING screen If the MATRIX channels are used individually If the MATRIX channels are paired MIX CHANNEL 1 MIX CHANNEL 2 MIX CHANNEL 1 MIX CHANNEL 2 MIX to MATRIX VIEW screen When the MTRX from MIX button is on BSEND LEVEL/SEND POINT When the SEND LEVEL button is on When the SEND POINT button is on DSELECTED PARAMETER (currently selected parameter) Function Global Output Input AResponse graph SURR SETUP screen Page OUTPUT VIEW function AChannel BEQ CCompressor DInsert in Page AChannels BInsert CLevel meters DSignal flow SIGNAL FLOW screen Page AJOB SELECT BCAPTURE CBUFFERED CH (Channel in the buffer) DEXECUTE CH JOB (Channel job) screen Page Page Function Global 3 4 Output Input functions INPUT PATCH screen DIRECT OUT PATCH screen Function Global 4 5 Output Input EGrid FOutput port GInput port HLIBRARY button Page NAME screen INPUT HA/INSERT function INSERT 1-24 screen INSERT 25-48 screen INSERT STIN screen Page INPUT /EQ function EQ PARAM (EQ parameter) screen Page /ATT 1-48 (Phase/Attenuation 1-48) screen /ATT STIN/FXRTN (Phase/Attenua- tion STIN/FXRTN) screen INPUT GATE/COMP function ELevel meters FType Key-in signal flow when Link= On GSTEREO LINK Key-in signal flow when Link= Off Function Global Output Input COMP PARAM (Compressor parame- ter) screen Page Page GATE LIBRARY screen INPUT DELAY function INPUT DCA/GROUP function DCA GROUP ASSIGN screen Function Global Output Input DSET BY CUE (Assign by [CUE] key) EQ LINK ASSIGN screen PAN/ROUTING function PAN/ROUTING function POST ON MIX bus 1 The signal will be sent from immediately after the [ON] key. POST ON/POST TO ST= POST TO ST Type = FIXED, Pairing = enabled Type = VARI, Pairing = disabled INPUT CHANNEL 2 PRE/POST button= POST PRE/POST button= PRE Type = VARI, Pairing = enabled EPRE EQ/PRE FADER 86 59 FFOLLOW PAN JMIX MINUS KInput channel Page Page BSEND LEVEL, PRE/POST (Send level / Send point) When the SEND LEVEL button is on When the PRE/POST button is on Function Global Output Input DSELECTED PARAMETER (currently selected parameter) LCR screen Function Global 5 6 7 Output Input SURR VIEW (Surround view) screen Function Global Output Input INPUT VIEW function M/S screen CH VIEW (Channel view) screen Page Function Global 1 32 Output Input FADER VIEW screen CH JOB screen BCAPTURE CBUFFERED CH (Channel in the buffer) DEXECUTE EPARAMETER SELECT FCH SELECT (Channel selection) Page EQ Library List Appendices GATE Library List GATE Library List Compressor Library List Compressor Library List Function Global Output Input Dynamics Parameters GATE A gate attenuates signals below a set THRESHOLD level by a specified amount (RANGE). DUCKING GATE section Compressor (COMP) An expander attenuates signals below a specified THRESHOLD by a specified RATIO. Expander (EXPAND) COMP section Time Series Analysis (RATIO= :1) Page Effect Library List Effect Library List This is a list of the built-in effects. Function Global Two input, two output basic stereo delay. Effects Parameters REVERB HALL, REVERB ROOM, REVERB STAGE, REVERB PLATE One input, two output hall, room, stage, and plate reverb simulations, all with gates. EARLY REF. GATE REVERB, REVERSE GATE MOD. DELAY One input, two output basic repeat delay with modulation. Two input, two output chorus effect. One input, two output 3-tap delay (left, center, right). DELAY LCR Function PM5D/PM5D-RH V2 / DSP5D Owners Manual Reference section 327 Global One input, two output high-quality pitch shifter. Two input, two output 16-stage phaser. DUAL PITCH Two input, two output pitch shifter. Two input, two output dynamically controlled filter. Two input, two output ring modulator. ROTARY Function Global One input, two output reverb and chorus effects in series. Two input, two output dynamically controlled phaser. Output REV+FLANGE One input, two output reverb and flanger effects in One input, two output reverb and flanger effects in series. REVFLANGE REV+SYMPHO. Function Global One input, two output delay and reverb effects in parallel. Output Input DELAYREV One input, two output delay and reverb effects in series. One input, one output basic sampler. DISTDELAY One input, two output distortion and delay effects in Function Global Output Input ST REVERB COMP276 COMP276S COMP260 COMP260S Function Global Output Input EQUALIZER601 Effects and tempo synchronization Function Global Output Input Scene Memory/Effect Library to Program Change Table Preset Bank/Ch# 1 Preset Bank/Ch# 2 Scene Memory/Effect Library to Program Change Table Preset Bank/Ch# 3 Preset Bank/Ch# 4 Function Global Preset Bank/Ch# 16 Preset Bank/Ch# 12 Output Bank/Ch# _ Parameters that can be assigned to control changes Parameters that can be assigned to control changes Function Global Output Input Control change parameter assignments PRESET CHANNEL1 PRESET CHANNEL2 Function Global Output Input PRESET CHANNEL3 PRESET CHANNEL4 Function Global Output Input PRESET CHANNEL5 PRESET CHANNEL6 Function Global Output Input PRESET CHANNEL7 PRESET CHANNEL8 Function Global Output Input PRESET CHANNEL9 PRESET CHANNEL10 Function Global Output Input PRESET CHANNEL11 PRESET CHANNEL12 Function Global Output Input PRESET CHANNEL13 PRESET CHANNEL14 Function Global Output Input PRESET CHANNEL15 PRESET CHANNEL16 Function Global Output Input CHANNEL _ NRPN parameter assignments Page NRPN parameter assignments Page Channel Library List Channel Library List Function Global Output Input List of parameters available for Pair, Recall Safe or OUTPUT ISOLATION operation Input channels MIX channels List of parameters available for Pair, Recall Safe or OUTPUT ISOLATION operation MATRIX channels STEREO channels Other Function Global Output Input Parameters that are copied when pair- ing is enabled MIDI Data Format 1 CHANNEL MESSAGE 1.1 NOTE OFF (8n) 1.2 NOTE ON (9n) 1.3 CONTROL CHANGE (Bn) 2 SYSTEM REALTIME MESSAGE 2.1 TIMING CLOCK (F8) 2.2 ACTIVE SENSING (FE) 2.3 SYSTEM RESET (FF) 3 System Exclusive Message 4. PARAMETER CHANGE details 4.1 Current Scene, Setup, Backup, Input Patch, Output Patch, HA Data Parameter change 4.2 Current Scene, Setup, Backup, Input Patch, Output Patch, HA Data Parameter request 4.3 Function Call Library Store/Recall (Parameter change) PM5D/PM5D-RH V2 / DSP5D Owners Manual Reference section 371 4.4 Function Call Library Edit (Parameter change) 4.5 Function Call Library Attribute Page 4.6 Exist Library Range 4.7 Function Call Collection Store PM5D/PM5D-RH V2 / DSP5D Owners Manual Reference section 375 4.8 Function Call Module 4.9 Function Call Channel 4.10Level Meter Data Parameter change 4.11Time Counter Data Time Code Warning Messages Warning Messages Error Messages Troubleshooting Troubleshooting General Specications General Specifications Analog Input (1-48) Analog Input (ST IN1-4 [L,R]) Oscillator Analog Input (2TR IN ANALOG1,2 [L,R]) Digital Input (2TR IN DIGITAL1-3) Talkback Input Page Input/output characteristics Analog Input Characteristics (PM5D) Analog Input Characteristics (PM5D-RH) Function Global Output Input Analog Input Characteristics (DSP5D) Digital Input Characteristics (PM5D, PM5D-RH) Digital Input Characteristics (DSP5D) Digital Output Characteristics (PM5D, PM5D-RH) Function Global Output Input Channel Status of 2TR OUT DIGITAL 1,2 Control I/O Characteristics (PM5D, PM5D-RH) Control I/O Characteristics (DSP5D) SLOT 1-4 (PM5D, PM5D-RH)/SLOT 1-2 (DSP5D) Characteristics Function Global Electrical characteristics All faders are nominal when measured. Output impedance of signal generator:150ohms Fs= 88.2 kHz or 96 kHz @20 Hz40 kHz, referenced to the nominal output level @1 kHz Gain Error @1 kHz Total Harmonic Distortion Fs= 44.1 kHz or 48 kHz Hum & Noise EIN= Equivalent Input Noise Dynamic Range Sampling Frequency Input Indicator Level Function Global Output Input Fs= 88.2 kHz or 96 kHz @20 Hz-40 kHz, referenced to the nominal output level @1 kHz Dynamic Range Sampling Frequency Function Global Processor Other Functions Input Function Libraries Output Function Pin Assignment Pin Assignment 6 9 CASCADE IN CASCADE OUT HA REMOTE RS422 REMOTE Dimensions 12313 25 1416 15 Unit: mm PM5D-RHPM5D Page Index Symbols Numerics A B 398 F G H I K L M N O 400 P R S T U V W Page PM5D/PM5D-RH Block Diagram DSP5D Block Diagram CH 1(...48) [OMNI OUT](1-24) x 4 INSERT IN PM5D Level Diagram Digital Analog DigitalAnalog Digital Analog Analog PM5D-RH Level Diagram Digital DigitalAnalog Digital Analog DSP5D Level Diagram Digital DigitalAnalog Digital Analog CANADA NORTH AMERICA CENTRAL & SOUTH AMERICA EUROPE AFRICA MIDDLE EAST ASIA OCEANIA