Manuals / ZyXEL Communications / Computer Equipment / Network Router

ZyXEL Communications Prestige 128 user manual Restore Configuration, Software Update

Models: Prestige 128

1 157

Download 157 pages 54.29 Kb

Page 141

highly recommended once your Prestige configuration is functioning.

You need to download the configuration onto disk. Procedure for downloading varies depending on the type of software used to access the Prestige but you must use the XMODEM protocol to perform the download.

Restore Configuration

Selecting option 6 from Menu 24 - Maintenance will restore backup configuration from disk to the Prestige. You need to upload a backup file to the Prestige. Procedure for uploading varies depending on the type of software used to access the Prestige but you must use the XMODEM protocol to restore the configuration.

Keep in mind that configuration is stored on flash ROM in the Prestige so even if power failure were to occur, your configuration is safe.

Software Update

Software updates are only possible through the RS-232 cable connection. You cannot use telnet to update the software version of your Prestige. Note that this function will delete the old software before installing the new software. Do not attempt to utilize this menu unless you have the new software version. There are two different software updates: RAS code and ISDN code.

∙RAS and ISDN code update - Type atur and wait until the Prestige responds with an OK to begin uploading the new software (upload procedure varies depending on the type of software used to access the Prestige). You must use the XMODEM protocol to perform the upload. After uploading is successful, type atgo to start your Prestige. Below is an example of downloading RAS and ISDN using PCPLUS.

128 System Maintenance

Image 141

ZyXEL Communications Prestige 128 user manual Restore Configuration, Software Update

Contents

JiH5 ACCESSING INTERNET & INTRANETPrestige User’s Manual VersionZyXEL Limited Warranty Copyright 1997 by ZyXEL AcknowledgmentsFCC Part 15 Information Information for Canadian Users Page ∙ E-mail Contacting ZyXELZyXEL Communications Corporation 1 Introduction Contents3 Installation 4 Configuring for Internet Access2 Before You Begin 6 Dial-In Configuration 5 Remote Node Configuration7 TCP/IP Configuration 8 Novell IPX Configuration13 Telnet Configuration and Capabilities 10 Filter Configuration14 System Maintenance 11 SNMP15 Troubleshooting 16 ISDN Switch Types17 Index xiii Features Ease of InstallationIntroduction Multiple Networking Protocol Support ISDN Basic Rate Interface BRIStandard Phone Jack Dial On DemandDHCP Support Dynamic Host Configuration Protocol RADIUS Remote Authentication Dial In User ServiceFull Network Management PPP SecurityApplications For Your Prestige Internet AccessData Compression Networking CompatibilityTelecommuting Server What This Manual CoversWhat This Manual Doesn’t Cover Other ResourcesPacking List Additional Installation Requirements 8 Introduction Road Map and Flow Before You BeginCompleting the Worksheet Figure 2-1 Installation Guide10 Before You Begin Ordering Your ISDN Line Collecting General Setup InformationSwitch Type Collecting ISDN Phone Line InformationGeography No of Phone #sAmerica, select your ISDN switch type. For DSS1 and 1TR6, verify this field to make sure that you have the proper firmware loaded 14 Before You Begin Collecting Ethernet Setup InformationNumber of Host IDs IP Subnet MaskNumber of Bits Before You BeginISDN Setup Information General Setup InformationPrestige Setup and Installation Worksheet 16 Before You BeginDSS1 ISDN North America ISDN∙ 1st Telephone Number ∙ Analog Call check one∙ A/B Adapter 2 Number & Subaddress 1TR6 ISDN∙ Outside Line Prefix Number ∙ PBX Number S/T Bus Number∙ A/B Adapter 2 Number Ethernet Setup Information∙ Outside Line Prefix Number ∙ PBX Number S/T Bus Number20 Before You Begin Installation Connecting Your Computer and Your PrestigeA Warning On Connection Cables Connecting an ISDN Line to your Prestige Connecting the RS-232 Cable to your PrestigeConnecting a Telephone/Fax to your Prestige 22 InstallationConnecting an Ethernet Cable to your Prestige ∙ UTP∙ AUI Prestige Front Panel Connecting a Power Adapter to your PrestigeFigure 3-3 Power on Messages Powering On Your PrestigeFigure 3-4 Login Screen Navigating Through the System Management Terminal InterfaceMain Menu, where typing 99 is the only method to exit the SMT 28 Installation System Management Terminal Interface SummaryFigure 3-5 SMT Main Menu Menu TitleGeneral Setup North American ISDN ISDN Setup1. Switch Type - Verify the switch type information with your telephone company. For North America, select the type of switch used by your telephone company. If your switch type is not currently shown, press the space bar to change to the next switch repeat until you see the correct switch type. The Prestige will not be able to place or to receive calls if the wrong switch type is specified. If you are not sure, contact your telephone company to confirm the exact switch type DSS1 & 1TR6 ISDN 6. Dial Prefix to Access Outside Line - Enter the prefix number if the Prestige is connected to an ISDN PBX. This number will be added to all outgoing calls and should be no longer than 3 digits. Otherwise, leave this field blank 34 Installation General Ethernet Setup Ethernet SetupFigure 3-11 Menu 3.1 - General Ethernet Setup TCP/IP Ethernet Setup and DHCPFigure 3-12 Menu 3.2 - TCP/IP Ethernet Setup 38 Installation Bridge Ethernet Setup Novell IPX Ethernet SetupRefer to the chapter on Novell IPX configuration Refer to the chapter on Bridging configurationConfiguring for Internet Access Configuring for Internet Access IP Addresses and the InternetFigure 4-2 Menu 4 - Internet Access Setup Internet Access Configuration5. My Login Name - Enter the login name given to you by your ISP 44 Configuring for Internet Access Single User AccountIn summary Configuration for Single User Account Configuring Backup ISP Accounts 48 Configuring for Internet Access Configuring for Internet Access 50 Remote Node Configuration Remote Node ConfigurationFigure 5-1 Menu 11 - Remote Node Setup Remote Node ConfigurationFigure 5-2 Menu 11.1 - Remote Node Profile 52 Remote Node Configuration ∙ PAP sends the user name and password in plain text 54 Remote Node Configuration 18. Telco Options Allocated Budget min - This field will set a budget outgoing call time for the Remote Node. The default for this field is 0 for no budget control 56 Remote Node Configuration Bandwidth on DemandEditing PPP Options 58 Remote Node Configuration ∙ 128 - Two channels will be used when a packet triggers a call∙ CISCO PPP - Cisco PPP options will be used ∙ 64 - Only one channel will be usedRemote Node Configuration to confirm your selections, or press ESC to cancel your selections60 Dial-In Configuration Dial-In ConfigurationTelecommuting Dial-In Server ApplicationFigure 6-1 Example of Remote User Telecommuter Figure 6-2 Example of a Dial-In Server Application Default Dial-In Setup∙ None - No CLID is required 64 Dial-In Configuration 11. IP Pool IP Start Addr - This field is active only if you 66 Dial-In Configuration Dial-In Users SetupFigure 6-5 Menu 14.1 - Edit Dial-in User Figure 6-4 Menu 14 - Dial-in User Setupare displayed with a - minus sign at the beginning of the name in Menu More on CLID IP Subnet Mask TCP/IP ConfigurationTCP/IP Configuration LAN-to-LAN ApplicationRemote Node Setup See page for more information on the Single User Account feature 74 TCP/IP Configuration Static Route SetupFigure 7-4 Static Routing Example Figure 7-5 Menu 12 - Static Route Setup - Main Menu76 TCP/IP Configuration Figure 7-6 IP Static Route Setup6. The Metric and the Private parameters have the same meaning as those in the Remote Node Setup IPX Network Environment Novell IPX ConfigurationFrame Type Network NumbersPrestige on LAN with Server Prestige on LAN without ServerFigure 8-1 Prestige Operating in IPX Environment IPX Spoofing IPX Ethernet Setup∙ ∙ ∙ Ethernet ∙ SNAP 82 Novell IPX Configuration Remote Node SetupLAN-to-LAN Application Figure 8-3 LAN-to-LAN application1. Route - Make sure IPX is among the protocols in the Route field 84 Novell IPX Configuration Static Route SetupFigure 8-6 Menu 12.2 - Edit IPX Static Route Figure 8-5 NetWare Servers on Both Sides of the Link86 Novell IPX Configuration Novell IPX Configuration Bridging Configuration 88 Bridging ConfigurationIPX Spoofing Bridge Ethernet Setup Figure 9-1 Bridge Ethernet Setup 90 Bridging ConfigurationLAN-to-LAN Application need to configure a Remote Node in order to dial out to another office Remote Node SetupDefault Dial-In Setup for Bridge Bridge Static Route Setup92 Bridging Configuration Figure 9-3 Menu 12.4 - Bridge Static Route About Filtering Filter ConfigurationConfiguring a Filter Set Prestige’s Filter StructureFilter Configuration ∙ # - Refers to the filter rule number ∙ Pr - Protocol ∙ SA - Source Address ∙ SP - Source Port number TCP/IP Filter Rule Configuring a Filter Rule∙ Yes ∙ No 100 Filter Configuration ∙ Yes - filter match only established TCP connections Figure 10-5 Menu 21.1.1 - Generic Filter Rule Generic Filter RuleNovell IPX Filter Rule ∙ None ∙ RIP Request ∙ RIP Response ∙ SAP Request ∙ SAP Response Configuring Your Prestige For SNMP Support SNMPAbout SNMP SNMP Figure 11-1 Menu 22 - SNMP Configuration108 SNMP SNMP Using RADIUS Authentication Installing a RADIUS ServerSystem Security Configuring the Prestige for RADIUS Authentication This will bring you to Menu 23.2 - System Security - External Server Adding Users to the RADIUS Database Using RADIUS Authentication for CLIDConfiguring the SMT Password 5. Re-type your new system password for confirmation purposes and press ENTER About Telnet Configuration Telnet Configuration and CapabilitiesSingle Administrator System TimeoutTelnet Capabilities System Status System Maintenance2. From this menu, select option 1. System Status 8. TXPkt - the number of transmitted packets on this channel Figure 14-3 LAN Packet Which Triggered Last Call Terminal Baud RateLog and Trace Syslog And Accounting View Error LogDiagnostic Figure 14-6 Menu 24.4 - System Maintenance - Diagnostic 126 System Maintenance Backup Configuration Software Update Restore ConfigurationCommand Interpreter Mode Call ControlFigure 14-9 Example of uploading RAS using PCPLUS Figure 14-10 Menu 24.9.1 Call Control Parameters Call Control ParametersFigure 14-11 Blacklist BlacklistFigure 14-12 Budget Management Budget ManagementSystem Maintenance Problems Starting Up the Prestige TroubleshootingNone of the LEDs are on when you power up the Prestige Connecting the RS-232 cable, cannot access the SMTProblems With the ISDN Line The ISDN initialization failedThe ISDN loopback test failed Problems with the LAN Interface Problems Connecting to a Remote Node or ISPCan’t PING any station on the LAN Problems Connecting to a Remote User ISDN Switch Types Provisioning For U.S. SwitchesProvisioning For the AT&T 5ESS Switches Setting Provisioning FeatureProvisioning Feature SettingProvisioning Feature Provisioning For the Northern Telecom SwitchSetting Provisioning FeatureSetting Provisioning FeatureISDN Switch Types EKTSIndex See IPX PABX IOC, 11. See ISDN Ordering Code IP Address, 14144 Index