Husqvarna 1030 BioClip, 1200 Maintenance schedule, Daily Maintenance interval, Hours, 100 300

Page 19

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance which should be conducted on the machine. For the items which are not described in these instructions go to an authorised service workshop.

 

 

Daily

Maintenance interval

Maintenance

Page

main-

 

in hours

tenance

 

 

 

 

25

50

100

300

 

 

 

 

before start

 

 

 

 

 

 

 

Check the engine’s oil level

19

 

 

 

 

Check the engine’s cooling air inlet

19

 

 

 

 

Check the fuel pump’s air filter

19

 

 

 

 

Check the transmission’s air inlet

20

 

 

 

 

Check the transmission’s oil level

20

 

 

 

 

Check the steering wires

21

 

 

 

 

Check the brakes

22

 

 

 

 

Check the battery

22

 

 

 

 

Check the safety system

22

 

 

 

 

Check screws and nuts

 

 

 

 

Check for fuel and oil leakage

 

 

 

 

Clean the air filter’s pre-filter (foam plastic) 2)

23

 

 

 

 

Check the cutting unit

24

 

 

 

 

Check the tyre pressures (60 kPa)

30

 

 

 

 

Adjust the brakes

22

 

 

 

 

Check the V-belts

 

 

 

 

Change the engine oil 1)

27

 

 

 

 

Lubricate joints and shafts 3)

28

 

 

 

 

Check and adjust the throttle wire

29

 

 

 

 

Replace the air filter’s pre-filter and paper filter 2)

23

 

 

 

 

Replace the oil filter

28

 

 

 

 

Replace the fuel filter

30

 

 

 

 

Replace the plugs

 

 

 

 

Clean the engine’s and the hydrostat’s cooling flanges 2,4)

 

 

 

 

Check the valve clearance 4)

 

 

 

 

Check the valves and seats 4)

 

 

 

 

 

 

 

 

 

 

 

1)First change after 8 hours. 2) During dusty conditions cleaning and replacement should be more frequent. 3) For daily use of the machine lubrication should be conducted twice a week. 4) Conducted by authorised service workshop.

= Described in these instructions.

= Not described in these instructions.

!WARNING!

No service procedures must be conducted on the engine or cutting unit unless:

The engine is switched off.

The parking brake is applied.

The ignition key is removed.

The cutting unit is disengaged.

The ignition cables are removed from the plugs.

English – 17

Image 19
Contents 101 89 Rider 1030 BioClip RiderSvenska Contents II. Slope operation Safety InstructionsSafe operation practices for ride-on mowers General operationIV. Service Read the instructions Explanation of SymbolsGeneral use These instructions are for your safety. Read them carefullyDo as follows Driving on slopesChildren MaintenanceDo not do the following Never drive the machine in an enclosed space Presentation PresentationLocation of the controls Choke lever Throttle controlSpeed limiter Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of the cutting heightParking brake SeatBefore starting DrivingStarting the engine Driving the machine Cutting tips MAX Stopping the engineDisengage lever Hours MaintenanceMaintenance schedule Daily Maintenance intervalRight-hand fender Dismantling of the machine hoodsEngine hood Front hoodCheck the engine’s cooling air intake Check the engine’s oil levelChecking of the fuel pump’s air filter Check the transmission’s oil level Check the transmission’s air intakeChecking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Checking and adjusting the brakeCheck the level of the battery acid Check the safety systemReplacing the air filter Do not use compressed air to clean the paper filterMaintenance Checking and adjusting the cutting unit’s parallelism Checking the blades Dismantling the cutting unitChanging the oil Lubrication Replacement of the oil filterGeneral lubrication Checking and adjustment of the throttle wire Checking the tyre pressure Replacement of the fuel filterProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage Wiring Diagram Rider 1030 Bioclip, Rider Technical DataEnglish «*2h6+¬ English «*2h6+¬