While Operating, Maintenance and Storage

RULES FOR SAFE OPERATION

•CORD SETS: Make sure your cord set is in good condition. When using a cord set, be sure to use a cord that is heavy enough to carry the current that your unit will draw. An undersized cord set will cause a drop in line voltage resulting in loss of power and overheating. See the operator’s manual for the unit that will power this add-on for the recommended cord size.

•Inspect all extension cords and the unit power connection periodically. Look closely for deterioration, cuts or cracks in the insulation. Also inspect the connections for damage. Replace the cords if any defects or damage appear.

•Prevent disconnection of the straight shaft trimmer powerhead from extension cord during operation by using a plug-receptacle retaining strap, connector, or by making a knot as shown below:

Extension	Straight Shaft	Extension	Straight Shaft
Cord	Trimmer Cord	Cord	Trimmer Cord

•Avoid dangerous environments. Never operate your unit in damp or wet conditions. Moisture is a shock hazard.

•Do not use the unit in the rain. Do not use in or around water.

•Do not handle the plug or unit with wet hands or standing on any wet surfaces.

•Do not leave the unit plugged in when not in use, changing attachments or add-ons, or while being serviced.

WHILE OPERATING

•Keep bystanders, especially children and pets, at least 50 ft (15 m) away.

•Wear safety glasses or goggles that are marked as meeting ANSI Z87.1 standards, and ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty.

•Wear heavy, long pants, boots, gloves and a long sleeve shirt. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level.

•Use the unit only in daylight or good artificial light.

•Use the right tool. Only use this tool for the purpose intended.

•Do not force unit. It will do the job better and with less likelihood of injury at a rate for which it was designed.

•Do not overreach, take extra care when working on steep slopes or inclines. Always keep proper footing and balance.

•Always hold the unit with both hands when operating. Keep a firm grip on both the front and rear handle or grips.

•Keep hands, face, and feet at a distance from all moving parts. Do not touch or try to stop the cutting attachment when it is rotating. Do not operate without guards in place.

•Do not operate the engine faster than the speed needed to do the job. Do not run the engine at high speed when not in use.

•Always stop the engine/motor when operation is delayed or when walking from one location to another.

.• If you strike or become entangled with a foreign object, stop the engine/motor immediately and check for damage. Have any damage repaired before attempting further operations.

•Stop the unit IMMEDIATELY if you feel excessive vibration. Vibration is a sign of trouble. Inspect thoroughly for loose nuts, bolts or damage before continuing. Repair or replace affected parts as necessary.

•Stop and switch the unit to off for maintenance, repair, or for changing add-ons or other attachments. The unit must be stopped and the cutting head no longer turning to avoid injury.

•Use only Genuine Factory Parts™ and accessories for this unit. These are available from your authorized service dealer. Use of any unauthorized parts or accessories could lead to serious injury to the user or damage to the unit, and void your warranty.

MAINTENANCE AND STORAGE

•Allow the unit to cool before storing or transporting. Be sure to secure the unit while transporting.

•Store the unit in a locked up and dry or high and dry place to prevent unauthorized use or damage, out of the reach of children.

•Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean unit and labels with a damp sponge. Clean after each use.

•Keep these instructions. Refer to them often and use them to instruct other users. If you loan someone this unit, also loan them these instructions.

•Only qualified personnel should perform any repairs or maintenance procedures that are not described in this manual.

•Check shear bolts, engine mounting bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

•Inside a building store the machine away from ignition sources. Allow the engine to cool before storing in any enclosure.

•Always refer to the Operator’s Manual instructions for important details if the unit is to be stored for an extended period.

•Do not attempt to repair the machine unless you have the proper tools, and instructions for disassembly and repair of the machine.

SAVE THESE INSTRUCTIONS