Troy-Bilt 769-00425A manual Speedspool Replacement Parts, Cleaning, Storage, Transporting

Page 11

MAINTENANCE AND REPAIR INSTRUCTIONS

2.Pull out the bump knob, spring, and foam seal (Fig. 14).

3.Pull the inner reel with existing line from the outer spool (Fig. 14).

4.Remove any existing line from the inner reel before cleaning. Remove any debris or grass from the knob, spring, inner reel, and foam seal. Wash the inner reel with warm soapy water (Fig. 17).

Inner Reel

Fig. 17

5.Clean the shaft and the inner surface of the outer spool. To clean the shaft underneath the plunger, press down on the plunger (Fig. 18). Remove any dirt or debris from the shaft.

NOTE: The inner reel must be totally dry before reinstalling it into the outer spool. Do not lubricate the inner reel or outer spool assembly.

6.Place the inner reel into the outer spool.

7.Place the bump knob, spring, and foam seal into the inner reel (Fig. 14).

8.Press the bump knob down and tighten clockwise.

9.Install new line as described in Line Installation for the SpeedSpool®

Shaft

Plunger

Fig. 18

SPEEDSPOOL® REPLACEMENT PARTS

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472 Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460 Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465 Foam Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181467 Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464 Bump Head™ Assembly . . . . . . . . . . . . . . . . . . . 181468 (Bump Knob, Inner Reel, Spring, )

These SpeedSpool® replacement parts can be purchased from your local authorized dealer.

CLEANING

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.

STORAGE

Check unit before storage to be sure the equipment is in safe working condition.

Stop the engine or motor.

Store the unit indoors, in a dry and locked place, out of the reach of children.

Maintain or replace safety and instruction labels, as necessary.

For gas powerhead units

Allow the unit to cool before storing in any enclosure.

Drain fuel from unit. Never store the unit with fuel in the fuel tank inside a building where ignition sources are present such as hot water and space heaters, clothes dryers, etc.

TRANSPORTING

Allow the unit to cool before transporting.

Secure the unit while transporting.

For gas powerhead units

Drain fuel from unit.

Tighten fuel cap before transporting.

11

Image 11
Contents Operator’s Manual Introduction Table of ContentsBefore Operating Symbol MeaningRules for Safe Operation While Operating Maintenance and StorageSymbol Meaning Safety Alert Symbol Safety and International SymbolsApplications Know Your UnitAssembling the Coupler Installing the Add-OnsCheck Flex Shaft Engagement Prior to Using Operating InstructionsDecorative Trimming Adjusting Trimming Line LengthHolding the Trimmer Tips for Best Trimming ResultsWinding the Inner Reel With New Line Maintenance and Repair InstructionsLine Installation for the Speedspool SpeedSpool instructions Cleaning the SpeedspoolReleasing the Inner Reel Storage Speedspool Replacement PartsCleaning For gas powerhead unitsCause Action TroubleshootingCutting Head will not Advance Line Cutting Line Advances UncontrollablyStraight Shaft Trimmer ADD-ON SpecificationsPage Page Troy-Bilt LLC Manuel de Lutilisateur Entretien AvertissementTable DES Matières Tous NOS RemerciementsAvant Lutilisation Symbole SignificationConsignes DE Sécurité Pendant Lutilisation DE Lappareil Maintenance and StoragePortez DES Protections Yeux ET Oreilles Symboles DE Sécurité ET InternationauxSymbole Signification Symbole D’ALERTE DE Sécurité Avertissement Lisez LE Manuel DE LutilisateurApplications FAMILIARISEZ-VOUS Avec Votre AppareilMontage DU Coupleur Mode DemploiRetrait de laccessoire Installation de laccessoireCoupe Décorative Tenue DE LA DésherbeuseRéglage DE LA Longueur DU FIL Conseils Pour Bien DésherberRembobiner le fil neuf sur le moulinet intérieur Installation DU FIL DU SpeedspoolmdEntretien ET Réparations Déroulement du moulinet intérieur Installation dun moulinet pré-enrouléTransport NettoyageLE FIL DE Coupe Avance DE Manière Incontrôlée Cause SolutionDépannage LA Tête DE Coupe NE Fait PAS Avancer LE FILCaractéristiques Accessoire DE Désherbeuse À Arbre DroitRemarque F15 Garantie Limitée DU Fabricant Pour Manual Del Operador Indice DE Contenidos Introduccion¡ADVERTENCIA Antes DE LA Operación Normas Para UNA Operacion SeguraSimbolo Significado Mantenimiento Y Almacenaje Durante LA OperacionUSE Protección Ocular Y Auditiva Simbolos DE Seguridad E InternacionalesSimbolo Significado Simbolo DE Alerta DE Seguridad Advertencia LEA EL Manual DEL OperadorAplicaciones Conozca SU UnidadEnsamblaje DEL Acoplador Instrucciones DE OperaciónRecorte Decorativo Como Sostener EL RecortadorAjuste DE LA Longitud DE LA Linea DE Corte Consejos Para Obtener Mejores Resultados AL RecortarBobinado del carrete interior con línea nueva Instrucciones DE Mantenimiento Y ReparacionInstalación DE LA Linea Para EL Speedspool Desconexión del carrete interior Instalación de un carrete interior prebobinadoPara unidades a gasolina LimpiezaTransporte AlmacenamientoLA Línea DE Corte Avanza SIN Control Resolucion DE ProblemasLA Cabeza DE Corte no Hace Avanzar Linea Accesorio Recortador DE EJE Recto EspecificacionesNotas Issued 9/02 Garantía Limitada DEL Fabricante Para