Snapper NXT22875E, 7800696 Maintenance Drive Control Adjustment Storage Procedure, Fuel System

Page 18

Maintenance

Drive Control Adjustment

 

 

Storage Procedure

 

 

 

 

 

 

 

 

!

WARNING

!

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

with engine and blade running. STOP engine and blade.

Remove starter insert. Disconnect spark plug wire and

Remove starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components

secure away from spark plug. Engine and components are

are HOT. Avoid serious burns, allow sufficient time for all

HOT. Avoid serious burns, allow sufficient time for all com-

components to cool.

 

ponents to cool. Wear heavy leather gloves when handling

The drive control (A, Figure 16) should engage the transmis-

or working around cutting blades. Blades are extremely

sharp and can cause severe injury.

sion when the control is pushed forward, and should disen-

 

 

 

gage the transmission when pulled all the way back.

Prepare the mower for “end of season” storage as follows:

 

 

1. Disconnect the spark plug wire and secure away from

 

A

the spark plug.

 

2. Drain the fuel tank and let the engine run until all fuel is

 

 

 

 

out of the carburetor.

 

 

NOTE: If using a fuel stabilizer, there is no need to drain the

 

 

fuel tank. Refer to the section e titled ‘Fuel System’.

 

 

3. Use a brush

r c mpressed air to remove loose debris,

 

 

then use a damp cl th to wipe down the unit.

 

 

4. Tilt the mower up on its rear wheels and inspect the

Figure 16: Drive control

 

underside of

he deck. (Do not tilt the mower with the

 

spark pl g or

arburetor down.) Scrape away stubborn

 

 

If the transmission does not engage or disengage,

acc

m lation of grass with a putty knife and/or wire

adjustment may be performed as follows:

br

sh.

 

• If the transmission does not engage, rotate the turnbuckle

5. Lubricate all exposed metal with a light coating of oil to

(A, Figure 17) one-half turn to move the ferrules (B) out

prevent corrosion.

from the turnbuckle. Check and repeat as needed.

6. Carefully fold the handles, flexing the control cables to

• If the transmission does not disengage, rotate the tu n-

prevent cable damage.

buckle one-half turn to move the ferrules in toward the turn-

7. Store the mower in a shed or other dry area, protected

buckle. Check and repeat as needed.

 

from weather.

B

 

Fuel System

 

 

Fuel can become stale when stored over 30 days. Stale fuel

A

 

causes acid and gum deposits to form in the fuel system or

 

essential carburetor parts. To keep fuel fresh, use Briggs

 

 

 

Reproduction

 

 

& Stratton FRESH START® fuel stabilizer, available as a

 

 

liquid additive or a drip concentrate cartridge.

 

 

There is no need to drain gasoline from the engine if a fuel

 

 

stabilizer is added according to instructions. Run the engine

 

 

for 2 minutes to circulate the stabilizer throughout the fuel

 

 

system. The engine and fuel can then be stored up to 24

Figure 17: Adjusting the drive cable

 

months.

 

Caution: Incorrect adjustment can cause premature wear

If gasoline in the engine has not been treated with a fuel

and/or damage to the wheel drive components.

stabilizer, it must be drained into an approved container. Run

 

 

the engine until it stops from lack of fuel. The use of a fuel

 

 

stabilizer in the storage container is recommended to

 

 

maintain freshness.

18

www.snapper.com

Image 18
Contents Not Manual No Rev. BDate of Purchase Retailer EquipmentEngine Reproduction For Operator Safety From Previous ColumnFrom Previous From Previous Column Securely Do not store mower or fuel container inside whereDo not put hands or feet near or under rotating parts Operator Safety Safety and Operation Decals Serious bodily injury or deathExplanation of Operation Decals Features and Controls Contact your dealer if you have questionsFuel Recommendations Void he engine warrantyBefore Starting Fuel must meet these requirementsPropelling the Mower Handle Height AdjustmentOperation Starting the Mower Stopping the MowerOperation Cutting Height Adjustment Mulching OperationOperation Installing the Grass Bag Re 10 Installing the grass bagOperation Charging the Battery Operation Maintenance Reminder Maintenance Maintenance Chart Emissions ControlMaintenance Change Engine Oil Service Air Filter Recommended. Do not overfillWashout Port Check Safety Interlock SystemClean Debris Off Mower Turn on the water supply to the garden hoseMaintenance Drive Control Adjustment Storage Procedure Fuel SystemFuel tank empty Fill fuel tank with fresh fuel Build-up of debris on or around driveLoose dipstick Warranties BatteryDetermine warranty eligibility ReproductionYour Warranty Rights And Obligations Not For Slope Guide Specifications MowerEngine Eproduct ion For Equipo MotorCaracterísticas y mandos Operación Solución de problemas GarantíasSeguridad del usuario MantenimientoSeguridad del usuario Continuación de la columna previaLa esté cruzando Materiales puede rebotar hacia el usuarioReduzca la velocidad antes de realizar giros Camiones cerradosSeguridad del usuario Etiquetas transparentes de Seguridad y funcionamientoProducirse lesiones físicas graves o la muerte Reproduction Explicación del significado de las etiquetas FuncionamientoOfrecen únicamente como referencias y pueden diferir de Características y mandosPreguntas que formular Su concreto modelo. Contacte con su distribuidor si tieneAntes de empezar Recomendaciones sobre combustiblePropulsión del cortacésped Operación Encendido del cortacéspedAjuste de altura del mango Detención del cortacéspedLos componentes se enfríen Operación Ajuste de altura de corteFuncionamiento de la desmenuzadora Tire de la palanca de ajuste de la altura de corte aTejida y están sometidas al deterioro y el desgaste durante Operación Instalación de la bolsa de céspedLas bolsas del receptor de césped están fabricadas con tela Su uso normal. Revise el estado de la bolsa antes de usarlaCargadores Aumentadores con la batería Operación Carga de la bateríaÁrea donde se realiza la carga de la batería. Nunca use Mantenga cualquier chispa, llama o fuego al jadosHoras de desactivación BujíaHoras totales Filtro de aireCada 8 horas o diariamente Primeras 5 horas Mantenimiento Tabla de mantenimientoControl de emisiones Cada 50 horas o anualmenteFiltro de aire Puerto de deslave Limpieza de los desechos delCortacésped En 3 segundosMantenimiento Sistema de combustibleSolución de problemas Motor GarantíasReproduction Equipo BateríaAbril Notas Guía DE Inclinaciones InclinaciónEspecificaciones Not Eproduct ion Date d’achat Distributeur ÉquipementMoteur Équipé d’un pare-étincelles, tel que défini dans ManipulationSécurité de l’opérateur Suite de la colonne précédenteFonctionnement Est en marcheSécurité de l’opérateur Autocollants de fonctionnement et De sécuritéLa mort Moins deux 2 minutes avant de faire le plein ’essence Tondre les pentes de biais, ne pas les monter ni les’éviter de les blesser Place Sac à herbe doCaractéristiques et commandes Recommandations de carburant Avant de démarrerFonctionnement Démarrage de la tondeuse Propulsion de la tondeuseArrêt de la tondeuse Fonctionnement Réglage de la hauteur de coupe Fonctionnement Installation du sac à herbe Dépose du bouchon de déchiquetageFonctionnement Recharge de la batterie Point d’accès de recharge de la batterieHeures de parcours Fonctionnement Aide-mémoire d’entretienTotal des heures Filtre à air HorlogeEntretien Tableau d’entretien Système de contrôle des émissionsEntretien Entretien du filtre à airEntretien Contrôler le système de verrouillage de sécurité Nettoyage de la tondeusePoint d’accès de rinçage Entretien Réglage de la commande ’entraînementSystème d’alimentation Dépannage Équipement GarantiesLa machine a été modifiée d’une MoteurAvril Reproduction Guide DE Pente Pentes Sur lesSpécifications

NXT22875EFCA, NXT22875E, 7800580, 7800696 specifications

The Snapper 7800580, 7800696, NXT22875EFCA, and NXT22875E are part of a cutting-edge line of outdoor power equipment designed for efficiency and user-friendliness. Tailored for both residential and commercial applications, these models showcase advanced engineering, robust features, and superior technology that cater to a variety of landscaping needs.

The Snapper 7800580 and 7800696 models feature powerful engines that deliver high torque and performance, ensuring that even the toughest mowing tasks are accomplished with ease. They include a self-propelled functionality that enhances maneuverability across various terrains, making them ideal for uneven lawns or large yards. The adjustable cutting height feature provides users with the ability to customize the grass length, leading to a perfect finish every time.

Both models incorporate Snapper’s signature cutting deck design, which optimizes airflow for better mulching, clipping discharge, and bagging. This innovative deck technology also reduces the risk of clogging, allowing for a smoother mowing experience. Additionally, these mowers are equipped with easy-start systems, enabling quick ignition without the hassle of priming.

Transitioning to the NXT22875EFCA and NXT22875E, these models are noted for their brushless motor technology, which provides increased efficiency and longevity compared to traditional motors. The brushless design reduces maintenance needs and extends the overall lifespan of the equipment. With an emphasis on battery-powered operation, both NXT22875 models are designed for low emissions, making them environmentally responsible choices for landscaping enthusiasts.

The NXT22875 series also boasts user-friendly features such as adjustable speed settings, allowing operators to tailor their mowing pace according to the terrain and grass conditions. Further enhancing the user experience, these mowers have ergonomic handles that reduce fatigue during extended use.

Safety is a key consideration in the design of all_four models, with features such as blade brake systems and durable construction that improves stability and reduces the risk of accidents. The combination of technological advancements, user-centric design, and powerful performance makes the Snapper 7800580, 7800696, NXT22875EFCA, and NXT22875E exceptional choices in the realm of outdoor power tools. Whether for professional landscaping or home lawn care, these models deliver quality, reliability, and versatility, meeting the diverse needs of users.