Snapper 7800580, 7800696 Before Starting, Fuel Recommendations, Fuel must meet these requirements

Page 9

 

Operation

Before Starting

5. Add fuel to the tank:

1. Check the guards, deflectors, grass bag, and covers to

• Make sure the mower is outside, where fumes can

safely dissipate.

make sure all are in place and securely tightened.

• Remove the fuel fill cap (C, Figure 2).

2. Check the blade control (A, Figure 1) and drive control

• Fill the tank with fuel. Refer to the section entitled ‘Fuel

(B) to insure they work freely.

Recommendations’. To allow for expansion of the fuel,

 

B

do not fill above the bottom of the filler neck (D).

• Reinstall the fuel fill cap.

 

6. Clean the exterior surfaces of the cutting deck and

 

engine of any accumulation of spilled fuel, dirt, grass,

 

oil, etc. Keep the engine air intake screen and cooling

 

fins clear at all times.

 

7. Charge the battery. Refer to the section entitled

 

“Charging the Battery”.

 

 

 

Fuel Recommendations

A

 

 

Fuel must meet these requirements:

 

 

 

• Clean, fresh, unleaded gasoline with

Figure 1: Mower controls

 

 

• A minimum of 87 octane / 87AKI (90 RON).

 

 

• Gasoline with up to 10% etha ol (gasahol) or up to 15%

 

 

 

3. Check the cutting height. Adjust to the desired height.

MTBE (methyl tertiary butyl ether) is acceptable.

Refer to the section entitled ‘Cutting Height Adjustment’.

• CAUTION: DO NOT use u

approved gasoline, such as E85.

4. Check the engine oil:

 

 

Do not mix o l n gas line

r modify the engine to run on

• Make sure the mower is on a level surface.

alternative fuels. Th s will damage the engine components

• Clean the oil fill area of any debris.

 

and void he engine warranty.

• Remove the dipstick (A, Figure 2) and wipe wi h a

The engine on this equipment is certified to operate on

clean cloth.

 

 

• Insert and tighten the dipstick.

 

 

gasoline. The emissions control system for this engine is EM

• Remove the dipstick and check the oil level. It should

(Engine Modifications).

 

be at the top of the full indicator (B)

the dipstick.

High Altitude

 

• If low, add oil (Briggs & Stratton warranty-certified

 

At altitudes over 5,000 feet (1524 meters), a minimum 85

SAE30 lawnmower oil is recommended) slowly into the

octane/85 AKI (89 RON) gasoline is acceptable. To remain

engine oil fill. Do not overfill. After adding oil, wait one

emissions compliant, high altitude adjustment is required.

minute and recheck the oil level.

 

 

 

 

Operation without this adjustment will cause decreased

• Replace and tighten the dipstick.

 

 

 

 

performance, increased fuel consumption, and increased

 

 

 

A

 

 

emissions.

 

 

 

Operation of the engine at altitudes below 2,500 feet (762

 

 

 

 

 

 

meters) with the high altitude kit is not recommended.

 

Reproduction

B

C

D

Figure 2: Oil and fuel fill

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual No Rev. B NotDate of Purchase Retailer EquipmentEngine Reproduction For From Previous Column Operator SafetyFrom Previous From Previous Column Securely Do not store mower or fuel container inside whereDo not put hands or feet near or under rotating parts Serious bodily injury or death Operator Safety Safety and Operation DecalsExplanation of Operation Decals Contact your dealer if you have questions Features and ControlsBefore Starting Void he engine warrantyFuel Recommendations Fuel must meet these requirementsOperation Starting the Mower Handle Height AdjustmentPropelling the Mower Stopping the MowerMulching Operation Operation Cutting Height AdjustmentRe 10 Installing the grass bag Operation Installing the Grass BagOperation Charging the Battery Operation Maintenance Reminder Emissions Control Maintenance Maintenance ChartRecommended. Do not overfill Maintenance Change Engine Oil Service Air FilterClean Debris Off Mower Check Safety Interlock SystemWashout Port Turn on the water supply to the garden hoseFuel System Maintenance Drive Control Adjustment Storage ProcedureFuel tank empty Fill fuel tank with fresh fuel Build-up of debris on or around driveLoose dipstick Determine warranty eligibility BatteryWarranties ReproductionYour Warranty Rights And Obligations Not For Slope Guide Specifications MowerEngine Eproduct ion For Motor EquipoSeguridad del usuario Solución de problemas GarantíasCaracterísticas y mandos Operación MantenimientoContinuación de la columna previa Seguridad del usuarioReduzca la velocidad antes de realizar giros Materiales puede rebotar hacia el usuarioLa esté cruzando Camiones cerradosSeguridad del usuario Etiquetas transparentes de Seguridad y funcionamientoProducirse lesiones físicas graves o la muerte Explicación del significado de las etiquetas Funcionamiento ReproductionPreguntas que formular Características y mandosOfrecen únicamente como referencias y pueden diferir de Su concreto modelo. Contacte con su distribuidor si tieneRecomendaciones sobre combustible Antes de empezarAjuste de altura del mango Operación Encendido del cortacéspedPropulsión del cortacésped Detención del cortacéspedFuncionamiento de la desmenuzadora Operación Ajuste de altura de corteLos componentes se enfríen Tire de la palanca de ajuste de la altura de corte aLas bolsas del receptor de césped están fabricadas con tela Operación Instalación de la bolsa de céspedTejida y están sometidas al deterioro y el desgaste durante Su uso normal. Revise el estado de la bolsa antes de usarlaÁrea donde se realiza la carga de la batería. Nunca use Operación Carga de la bateríaCargadores Aumentadores con la batería Mantenga cualquier chispa, llama o fuego al jadosHoras totales BujíaHoras de desactivación Filtro de aireControl de emisiones Mantenimiento Tabla de mantenimientoCada 8 horas o diariamente Primeras 5 horas Cada 50 horas o anualmenteFiltro de aire Cortacésped Limpieza de los desechos delPuerto de deslave En 3 segundosSistema de combustible MantenimientoSolución de problemas Reproduction Equipo GarantíasMotor BateríaAbril Notas Inclinación Guía DE InclinacionesEspecificaciones Not Eproduct ion Date d’achat Distributeur ÉquipementMoteur Manipulation Équipé d’un pare-étincelles, tel que défini dansSuite de la colonne précédente Sécurité de l’opérateurEst en marche FonctionnementSécurité de l’opérateur Autocollants de fonctionnement et De sécuritéLa mort ’éviter de les blesser Place Tondre les pentes de biais, ne pas les monter ni lesMoins deux 2 minutes avant de faire le plein ’essence Sac à herbe doCaractéristiques et commandes Avant de démarrer Recommandations de carburantFonctionnement Démarrage de la tondeuse Propulsion de la tondeuseArrêt de la tondeuse Fonctionnement Réglage de la hauteur de coupe Dépose du bouchon de déchiquetage Fonctionnement Installation du sac à herbePoint d’accès de recharge de la batterie Fonctionnement Recharge de la batterieTotal des heures Fonctionnement Aide-mémoire d’entretienHeures de parcours Filtre à air HorlogeSystème de contrôle des émissions Entretien Tableau d’entretienEntretien du filtre à air EntretienEntretien Contrôler le système de verrouillage de sécurité Nettoyage de la tondeusePoint d’accès de rinçage Entretien Réglage de la commande ’entraînementSystème d’alimentation Dépannage La machine a été modifiée d’une GarantiesÉquipement MoteurAvril Reproduction Pentes Sur les Guide DE PenteSpécifications

NXT22875EFCA, NXT22875E, 7800580, 7800696 specifications

The Snapper 7800580, 7800696, NXT22875EFCA, and NXT22875E are part of a cutting-edge line of outdoor power equipment designed for efficiency and user-friendliness. Tailored for both residential and commercial applications, these models showcase advanced engineering, robust features, and superior technology that cater to a variety of landscaping needs.

The Snapper 7800580 and 7800696 models feature powerful engines that deliver high torque and performance, ensuring that even the toughest mowing tasks are accomplished with ease. They include a self-propelled functionality that enhances maneuverability across various terrains, making them ideal for uneven lawns or large yards. The adjustable cutting height feature provides users with the ability to customize the grass length, leading to a perfect finish every time.

Both models incorporate Snapper’s signature cutting deck design, which optimizes airflow for better mulching, clipping discharge, and bagging. This innovative deck technology also reduces the risk of clogging, allowing for a smoother mowing experience. Additionally, these mowers are equipped with easy-start systems, enabling quick ignition without the hassle of priming.

Transitioning to the NXT22875EFCA and NXT22875E, these models are noted for their brushless motor technology, which provides increased efficiency and longevity compared to traditional motors. The brushless design reduces maintenance needs and extends the overall lifespan of the equipment. With an emphasis on battery-powered operation, both NXT22875 models are designed for low emissions, making them environmentally responsible choices for landscaping enthusiasts.

The NXT22875 series also boasts user-friendly features such as adjustable speed settings, allowing operators to tailor their mowing pace according to the terrain and grass conditions. Further enhancing the user experience, these mowers have ergonomic handles that reduce fatigue during extended use.

Safety is a key consideration in the design of all_four models, with features such as blade brake systems and durable construction that improves stability and reduces the risk of accidents. The combination of technological advancements, user-centric design, and powerful performance makes the Snapper 7800580, 7800696, NXT22875EFCA, and NXT22875E exceptional choices in the realm of outdoor power tools. Whether for professional landscaping or home lawn care, these models deliver quality, reliability, and versatility, meeting the diverse needs of users.
Top Page Image Contents