Murray 1737921, 1695720 manual Operate the Snow Thrower, Stop the Snow Thrower, Control Levers

OPERATION

WARNING: The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before beginning snow thrower operation. We recommend standard safety glasses or Wide Vision Safety Mask over spectacles.

OPERATE THE SNOW THROWER

CAUTION: Operation with a Snow Cab. Wind may blow exhaust gasses back towards the operator. If you notice the smell of exhaust, change direction of operation.

The most effective use of the snow thrower will be established by experi- ence, taking into consideration the terrain, wind conditions, and building location which will determine the direction of the discharge chute.

NOTICE: Do not throw snow toward a building as hidden objects could be thrown with sufficient force to cause damage.

1.Start the engine. See “To Start Engine” in this section.

2.Rotate the crank (C, Figure 5) to set the direction (left or right) of the discharge chute.

3.Pull the remote chute lever (D) back to discharge the snow down. Push the remote chute lever forward to discharge the snow high and far.

CAUTION: Before operating, make sure the area in front of the snow thrower is clear of bystanders or obstacles.

4.Fully press and hold the auger engage control (A) on the right-hand grip to begin auger rotation. Releasing the auger engage control will disengage the auger - unless the Free-Hand™ Control has been acti- vated.

12 Free-HandTMControl

CDE

B A

Control Levers Figure 5

5.Fully press and hold the traction and Free-Hand™ Control lever (B) on the left-hand grip to engage the traction drive and begin moving the snowthrower. To disengage the traction drive, completely release the lever.

6.When BOTH levers are depressed, the Free-Hand™ Control is acti- vated. This allows auger engage control to be released - YET AUGER ROTATION WILL CONTINUE - until the Free-Hand™ Control is re- leased.

NOTE: Always release the traction control lever before moving the speed select lever.

7.Use the speed select lever (E) to select the forward drive speed. Set the speed select lever to one of the following positions as determined by snow conditions:

1-2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4-5 Very Light

6Transport

NOTE: When clearing wet, heavy, snow, it is recommended that the ground speed of the unit be reduced, maintained full throttle and do not attempt to clear the full width of the unit.

8.To stop moving forward, release the traction control lever (B).

9.To move the snow thrower backwards, move the speed select lever into either first or second reverse position and engage the traction control lever.

STOP THE SNOW THROWER

1.Release the auger engage control (A, Figure 5).

2.Release the traction control lever (B).

3.Push the ON/OFF switch (A, Figure 14) to the OFF position and pull out the safety key (B).

WARNING: Read Operator’s Manual before operating machine. This machine can be dangerous if used carelessly.

•Never operate the snow thrower without all guards, covers, shields in place.

•Never direct discharge towards windows or allow bystanders near machine while engine is running.

•Stop the engine whenever leaving the operating position.

•Disconnect spark plug before unclogging the impeller housing or the discharge chute and before making repairs or adjustments.

•When leaving the machine, remove the safety key. To reduce the risk of fire, keep the machine clean and free from spilled gas, oil, and debris.

WARNING: Never run engine indoors or in an enclosed, poor ventilated area. Engine exhaust contains CARBON MONOXIDE, an ODORLESS and DEADLY GAS.

•Keep hands, feet, hair, and loose clothing away from any moving parts on engine and snow thrower.

•Temperature of muffler and nearby areas can exceed 150°F (66°C). Avoid these areas.

•DO NOT allow children or young teenagers to operate or be near snow thrower while it is operating.

13