Murray 1695720, 1737921 manual Belt Adjustment, Seconds, Adjusting Auger Drive Belt

Page 24

MAINTENANCE

BELT ADJUSTMENT

Traction Drive Belt

The traction drive belt has constant spring pressure and does not require an adjustment. If the traction drive belt is slipping, replace the belt. See au- thorized dealer.

Auger Drive Belt

If your snow thrower will not discharge snow, check the control cable adjust- ment. If it is correct, then check the condition of the auger drive belt. If it is damaged or loose, replace it (see authorized dealer).

1.Disconnect spark plug wire.

2.Remove screw (A, Figure 26) from belt cover (B). Remove belt cover.

3.Loosen nut on idler drive pulley (A, Figure 27) and move idler drive pulley towards belt about 1/8 inch (3 mm).

WARNING: Do not over-tighten, as this may lift the lever and cause the auger drive to be engaged without depressing the auger control.

4.Tighten nut.

5.With the aid of an assistant, engage the auger drive clutch. Check ten- sion on belt which is opposite idler pulley (B, Figure 27). Belt should deflect about 1/2 inch (12.5 mm) with moderate pressure. You may have to move idler pulley more than once to obtain the correct ten- sion.

6.Release the auger drive control lever. The auger must stop within five

(5) seconds.

7.If auger does not operate properly, stop engine and recheck drive linkage adjustments.

8.Reinstall belt cover (B, Figure 26). Tighten screw (A).

9.Whenever belts are adjusted or replaced, the cables will need to be adjusted (see “Check and Adjust the Cables” section).

10.Attach the spark plug wire.

 

B

 

A

Adjusting Auger Drive Belt

Figure 26

 

3

A

8

.

(125mm)

 

1/2”

 

Deflection

B

 

Check Tension on Auger Drive Belt

Figure 27

24

Image 24
Contents Operator’s Manual Manual Part NoWhere to Find Us Date PurchasedTable of Contents Operator Safety Keep a SafeRotating Parts Fire Explosion Shock Toxic Fumes Recommended Hot SurfaceSlow Engine Run Fast Engine StopTraction Control Engage DownOperation and Equipment Safety Moving Parts Maintenance and Storage Easy-TurnTMTraction Shift Decal Control Decal Auger Control Decal Main Dash DecalChute Danger Decal Features and Controls Engine and Snow Thrower ControlsFeatures and Controls Operation Before Operating Snow ThrowerOperate the Snow Thrower Stop the Snow ThrowerControl Levers Traction Lock Pins Traction Lock PinsEASY-TURNTMTRACTION Control Check the OIL Before Starting Engine Checking the OilFill the Fuel Tank Start the EngineStarting Engine Inserting Safety Key Stop the EngineStopping Engine Clear a Clogged Discharge Chute Operating TipsCable Adjustment After Each USEMaintenance Engine Maintenance Connecting Choke Control Knob Change the Spark PlugSnow Thrower Engine Adjust Skid Height Adjusting Skid HeightBelt Adjustment Adjusting Auger Drive BeltSeconds Check Tension on Auger Drive BeltBelt Guide Adjustment Check and Adjust the CablesAdjusting Belt Drive Adjusting Auger Drive CableTraction Drive Cable EASY-TURN Cable Adjustment Auger Shear PIN ReplacementStorage OFF Season StorageRemove from Storage Troubleshooting Problem Look for RemedyLimited Warranty WarrantiesBriggs & Stratton Emissions Control Warranty Provisions Specifications Clearing WidthChute Deflector Remote Chute Rotation Drive TypePage Page Manuel d’Utilisation Réf. fab DescriptionSouffleuse à neige MoteurDate d’achat Où nous trouverTable DES Matières Protection des oreilles Surface chauderecommandée pour une Ou modéréesRotatifs Manette de tarière Marche avant Point mort Marche arrièreSécurité de l’utilisation et de l’équipement Pièces en mouvement Sécurité du moteur suite Étiquettes du moteur Réf Réf Étiquette Tableau de bord principalRéf Auger Étiquette Étiquettes de sécurité Commandes DU Moteur ET DE LA Souffleuse À Neige Commandes de moteurPoignée de lanceur Sert à démarrer le moteur à la main Fontions ET Commandes Commandes de la soufleuse à neigeNe pas gonfler les pneus-dessus de la pression recommandée Avant D’UTILISATION Souffleuse À NeigeContrôler LES Pneus Vérifier la pression dair des pneusUtilisation DE LA Souffleuse À Neige Arrêter LA Souffleuse À NeigeLeviers de contrôle Levier Easy-Turntm relâché Facilement avec le moteur coupé Levier Easy-Turntm engagéEt au-dessus Et en dessousContrôler le niveau d’huile Remplir LE Réservoir D’ESSENCE Démarrer LE MoteurArrêter LE Moteur Insérer la clé de sécurité’arrêter le moteur Conseils D’UTILISATION Toujours utiliser un outil de nettoyage, pas les mainsOutil de nettoyage Autant que possible, projeter la neige dans le sens du ventAprès Chaque Utilisation Graissage DE L’ARBRE DE VIS Sans FIN Contrôles de graissageGraissage de la boîte d’engrenage de vis sans fin Pignon de rotation de goulotteVoir les huiles recommandées dans le tableau ci-contre Remarque Un excès d’huile peut perturber le fonctionnement18 C 0 F et au-dessus 18 C 0 F et en dessousRaccorder le bouton de commande de starter Changer LA Bougie D’ALLUMAGEDéposer le capot à neige Moteur de souffleuse à neigeRégler ou changer la bougie Régler LA Hauteur DES PatinsLes patins se règlent de la manière suivante Régler la hauteur des patinsAjustement DES Courroies Courroie d’entraînement de tractionCourroie d’entraînement de vis sans fin Obtenir la tension correcteAjustement DU Guide DE Courroie Contrôle ET Réglage DES CâblesCâble d’entraînement de vis sans fin Réglage guide de courroieCâble de commande de traction Changer LES Goupilles DE Cisaillement DE VIS Sans FIN SuivanteRemisage Hors Saison Sortir LA Souffleuse À Neige DU RemisageNettoyer la souffleuse à neige avec soin Démarrage difficile Le moteur a des ratésMoteur est chaud Le moteur caleGaranties Novembre Informations concernant la puissance théorique du moteur Bougie en platine longue durée Dispositif d’allumageDéflecteur de goulotte Distance Rotation de la goulotte Type d’entraînement