Sterling SXS Series specifications In-feed Hopper, Additional In-feed Device

Page 13

In-feed Hopper

The material in-feed flows through an in-feed hopper made to ensure the material is delivered safely and correctly.

NOTE: An optional top-hinged cover to prevent in-feed material fly-back during size reduction is available.

Special hopper with hydraulic cover

Additional In-feed Device

If the machine has an optional in-feed device, such as a conveyor belt, please refer to the additional information about the accessory in the manufacturer’s manual that accompanied the accessory. A special hopper for an in-feed with conveyor arrangement can be supplied as an option to the standard hopper.

Hopper for conveyor belt in-feed

BJ5-620

Chapter 2: Functional Description

13 of 73

Image 13

Contents SXS Extreme Duty Shredder Shipping Info Storage Storage, Disposal, TransportationDisposal TransportationTable of Contents How to Use This Manual SafetySafety Symbols Used in this Manual Responsibility General Safety RegulationsPage Remaining Risks BJ5-620 Safety Page Models Covered in This Manual Functional DescriptionGeneral Description Mechanical SectionMachine Standard Execution Typical Features and ComponentsMaterial In-feed Additional In-feed Device In-feed HopperRotor, Cutters, and Bed Knives DriveRotor, cutters, bed knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Belts and Ram Guards Safety MarkingsPersonal Protective Gear Re-operation Emergency Stop ButtonUnloading and Installing the Machine InstallationUncrating the Equipment Requirements at Application SiteElectrical Connections Connection of Emergency Stop Button Initial Start-up General AdviceChecking the Rotational Direction Machine Check Prior to Start-upPage Operation Operation ProceduresStart-up Emptying the Screen Hydraulic Set-up 12ml / r ec Shut-down Switch OFF MachinePreventative Maintenance Schedule MaintenanceMaintenance Plan Cleaning the Machine Preventative and Corrective MaintenanceChecking the Protective Devices Replacing the Rotor Replacing the Gear BoxDismounting the Rotor Replacing the Main Bearings Mounting the RotorDismounting the Main Bearings Lubricating the Main Bearings Mounting the Main BearingsShift Operation Replace Lubricant Check Lubrication IntervalsCheck lubricant quality Replacing or Refilling LubricantReplacing Lubricant Refilling lubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Replacing the Screen Tightening Torque of the ScrewsHydraulic Screen Support optional Checking the tension force of the V-belt BeltsCentres and 16mm sag Profile section Efficiency of x Newton LbsChecking V-belt condition, replacing V-belt Re-tensioning and relaxing the V-beltReplacing and Checking the Cutting Knife Mountings Working on the Cutting KnivesTorque Grade Bolt type Checking the Condition of the CuttersDismounting the Cutter Holders Dismounting the CuttersDismounting the Bed Knives Mounting the Cutter Holders Mounting the Cutters Make sure that the cutter holder fits properlyMake sure the cutter fits planar in the seat Mounting the Bed Knives Adjust the gap between cutter and bed knife to 0.8-1.0 mmSharpening Cutters and Bed Knives Setting the Cutting KnivesFix the knife cover plates BJ5-620 Maintenance Transporting and Storing the Cutting Knives Hydraulic MaintenanceHydraulic liquid recommendation Introduction TroubleshootingDepartment Problem Possible Cause Possible RemedyToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Appendix Warranty ReturnsReturned Material Policy Credit ReturnsTechnical Specifications Cutter mounting Drawings and DiagramsBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram SXS Spare Parts ListKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Pos Description Standard Supplier Hydraulic Unit Spare Parts ListSterling, Inc Th Street New Berlin, WI Technical Assistance