Sterling SXS Series specifications Mounting the Cutter Holders

Page 47

5.Clean the hexagon head socket of the knife mounting bolts (2) and the cover plates mounting bolts.

6.Loosen the cover plate mounting bolts using a high quality Allen key (10 mm). Knock the Allen key lightly with a hammer to loosen if necessary.

7.Take out the bolts and cover plates.

8.Loosen the knife adjusting screws for pulling and take them out.

9.Loosen the knife mounting bolts with Allen key (10 mm). Use a hammer to lightly knock key if necessary.

10.Take out the knife mounting bolt and knife.

WARNING! Danger of cutting caused by sharp knives at all times—even when rotor is at standstill. Serious Injury especially to the hands and fingers can occur. Wear protective gloves!

(1)Bed knife

(2)Knife mounting screws

(3)Knife holder

(4)Cover plates

(5)Knife adjusting screw for pushing

(6)Knife adjusting screw for pulling

(7)Cover plate mounting screws

2

6

5

3 4

1

7

Mounting the Cutter Holders

1.Clean the cutter pocket and the cutter holder.

2.Insert cutter holder into the pocket.

NOTE: Cutter holder must slide in easily. Do not damage the cutter holder surfaces with a hammer.

BJ5-620

Maintenance

47 of 73

Image 47

Contents SXS Extreme Duty Shredder Shipping Info Transportation Storage, Disposal, TransportationStorage DisposalTable of Contents Safety Symbols Used in this Manual SafetyHow to Use This Manual Responsibility General Safety RegulationsPage Remaining Risks BJ5-620 Safety Page Mechanical Section Functional DescriptionModels Covered in This Manual General DescriptionMaterial In-feed Typical Features and ComponentsMachine Standard Execution Additional In-feed Device In-feed HopperRotor, cutters, bed knives DriveRotor, Cutters, and Bed Knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Personal Protective Gear Safety MarkingsBelts and Ram Guards Re-operation Emergency Stop ButtonRequirements at Application Site InstallationUnloading and Installing the Machine Uncrating the EquipmentElectrical Connections Connection of Emergency Stop Button Machine Check Prior to Start-up General AdviceInitial Start-up Checking the Rotational DirectionPage Start-up Operation ProceduresOperation Emptying the Screen Hydraulic Set-up 12ml / r ec Shut-down Switch OFF MachineMaintenance Plan MaintenancePreventative Maintenance Schedule Checking the Protective Devices Preventative and Corrective MaintenanceCleaning the Machine Dismounting the Rotor Replacing the Gear BoxReplacing the Rotor Dismounting the Main Bearings Mounting the RotorReplacing the Main Bearings Lubricating the Main Bearings Mounting the Main BearingsReplacing or Refilling Lubricant Lubrication IntervalsShift Operation Replace Lubricant Check Check lubricant qualityReplacing Lubricant Refilling lubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Hydraulic Screen Support optional Tightening Torque of the ScrewsReplacing the Screen Profile section Efficiency of x Newton Lbs BeltsChecking the tension force of the V-belt Centres and 16mm sagChecking V-belt condition, replacing V-belt Re-tensioning and relaxing the V-beltChecking the Condition of the Cutters Working on the Cutting KnivesReplacing and Checking the Cutting Knife Mountings Torque Grade Bolt typeDismounting the Cutter Holders Dismounting the CuttersDismounting the Bed Knives Mounting the Cutter Holders Make sure the cutter fits planar in the seat Make sure that the cutter holder fits properlyMounting the Cutters Mounting the Bed Knives Adjust the gap between cutter and bed knife to 0.8-1.0 mmSharpening Cutters and Bed Knives Setting the Cutting KnivesFix the knife cover plates BJ5-620 Maintenance Transporting and Storing the Cutting Knives Hydraulic MaintenanceHydraulic liquid recommendation Introduction TroubleshootingDepartment Problem Possible Cause Possible RemedyToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Credit Returns Warranty ReturnsAppendix Returned Material PolicyTechnical Specifications Cutter mounting Drawings and DiagramsBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram SXS Spare Parts ListKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Pos Description Standard Supplier Hydraulic Unit Spare Parts ListSterling, Inc Th Street New Berlin, WI Technical Assistance