Sterling SXS Series specifications Tightening Torque of the Screws, Replacing the Screen

Page 41

Tightening Torque of the Screws

Refer to the table below.

Tensioning	Screws-
element (Type)	Tightening torque in Nm
1008	5,6
1108	5,6
1310	20
1315	20
1210	20
1215	20
1610	20
1615	20
2012	31
2017	31
2517	48
2525	48
3020	90
3030	90
3535	60
4040	102
4545	155
5050	185

Screw details

Number	Size (BSW)
2	1/4"
2	1/4"
2	3/8"
2	3/8"
2	3/8"
2	3/8"
2	3/8"
2	3/8"
2	7/16"
2	7/16"
2	1/16"
2	1/16"
2	5/8"
2	5/8"
3	1/2"
3	5/8"
3	3/4"
3	7/8"

Replacing the Screen

The condition of the screen must be checked regularly in order to keep the throughput of the shredder and the quality of the shredded material constant.

The screen may be damaged, dirty, or not suitable for the shredding material when:

•Screen holes too fine—overheating of the material can occur.

•Screen holes too course—shredded material can have larger pieces that are unacceptable.

Hydraulic Screen Support (optional)

1.Switch OFF the shredder at the main switch.

2.Safeguard main switch using a padlock.

3.Open the machine door.

4.Safeguard the machine door.

5.Pivot the screen support downwards by pushing the button screen open on the control box.

6.Remove the screen.

7.Put a new screen into the screen support.

BJ5-620

Maintenance

41 of 73

Image 41

Contents SXS Extreme Duty Shredder Shipping Info Storage Storage, Disposal, TransportationDisposal TransportationTable of Contents Safety Symbols Used in this Manual SafetyHow to Use This Manual Responsibility General Safety RegulationsPage Remaining Risks BJ5-620 Safety Page Models Covered in This Manual Functional DescriptionGeneral Description Mechanical SectionMaterial In-feed Typical Features and ComponentsMachine Standard Execution Additional In-feed Device In-feed HopperRotor, cutters, bed knives DriveRotor, Cutters, and Bed Knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Personal Protective Gear Safety MarkingsBelts and Ram Guards Re-operation Emergency Stop ButtonUnloading and Installing the Machine InstallationUncrating the Equipment Requirements at Application SiteElectrical Connections Connection of Emergency Stop Button Initial Start-up General AdviceChecking the Rotational Direction Machine Check Prior to Start-upPage Start-up Operation ProceduresOperation Emptying the Screen Hydraulic Set-up 12ml / r ec Shut-down Switch OFF MachineMaintenance Plan MaintenancePreventative Maintenance Schedule Checking the Protective Devices Preventative and Corrective MaintenanceCleaning the Machine Dismounting the Rotor Replacing the Gear BoxReplacing the Rotor Dismounting the Main Bearings Mounting the RotorReplacing the Main Bearings Lubricating the Main Bearings Mounting the Main BearingsShift Operation Replace Lubricant Check Lubrication IntervalsCheck lubricant quality Replacing or Refilling LubricantReplacing Lubricant Refilling lubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Hydraulic Screen Support optional Tightening Torque of the ScrewsReplacing the Screen Checking the tension force of the V-belt BeltsCentres and 16mm sag Profile section Efficiency of x Newton LbsChecking V-belt condition, replacing V-belt Re-tensioning and relaxing the V-beltReplacing and Checking the Cutting Knife Mountings Working on the Cutting KnivesTorque Grade Bolt type Checking the Condition of the CuttersDismounting the Cutter Holders Dismounting the CuttersDismounting the Bed Knives Mounting the Cutter Holders Make sure the cutter fits planar in the seat Make sure that the cutter holder fits properlyMounting the Cutters Mounting the Bed Knives Adjust the gap between cutter and bed knife to 0.8-1.0 mmSharpening Cutters and Bed Knives Setting the Cutting KnivesFix the knife cover plates BJ5-620 Maintenance Transporting and Storing the Cutting Knives Hydraulic MaintenanceHydraulic liquid recommendation Introduction TroubleshootingDepartment Problem Possible Cause Possible RemedyToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Appendix Warranty ReturnsReturned Material Policy Credit ReturnsTechnical Specifications Cutter mounting Drawings and DiagramsBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram SXS Spare Parts ListKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Pos Description Standard Supplier Hydraulic Unit Spare Parts ListSterling, Inc Th Street New Berlin, WI Technical Assistance