Sterling SXS Series specifications Connection of Emergency Stop Button

Page 24

WARNING! Use caution when operating specific equipment to prevent electrical shock. Installation, service, alterations, and/or modifications must only be done by qualified personnel and with high regard for safety. Not conforming to the requirements could result in bodily harm, death, or costly damage.

NOTE: Alterations to the wiring diagrams require approval. Failure to do this will exclude all guarantee claims.

The wiring schematics are located in the control panel.

Connection of Emergency Stop Button

The machine may only be operated with installed Emergency Stop buttons. An Emergency Stop button must be installed at the control cabinet and at the grinding material in-feed if no Emergency Stop buttons have been installed at the factory.

The control panel with the switches and Emergency Stop button must be installed near the machine. The distance should not exceed 5 m.

The distance between the floor and the lower edge of the control panel should be at least 1 m.

The connecting cables between the control panel and the machine must be protected against damage (cable tray, protective sleeve).

An additional Emergency Stop button has to be installed on the machine If the control box cannot be installed according to these rules.

BJ5-620

Installation

24 of 73

Image 24

Contents SXS Extreme Duty Shredder Shipping Info Storage, Disposal, Transportation StorageDisposal TransportationTable of Contents Safety How to Use This ManualSafety Symbols Used in this Manual General Safety Regulations ResponsibilityPage Remaining Risks BJ5-620 Safety Page Functional Description Models Covered in This ManualGeneral Description Mechanical SectionTypical Features and Components Machine Standard ExecutionMaterial In-feed In-feed Hopper Additional In-feed DeviceDrive Rotor, Cutters, and Bed KnivesRotor, cutters, bed knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Safety Markings Belts and Ram GuardsPersonal Protective Gear Emergency Stop Button Re-operationInstallation Unloading and Installing the MachineUncrating the Equipment Requirements at Application SiteElectrical Connections Connection of Emergency Stop Button General Advice Initial Start-upChecking the Rotational Direction Machine Check Prior to Start-upPage Operation Procedures OperationStart-up Emptying the Screen Hydraulic Set-up 12ml / r ec Switch OFF Machine Shut-downMaintenance Preventative Maintenance ScheduleMaintenance Plan Preventative and Corrective Maintenance Cleaning the MachineChecking the Protective Devices Replacing the Gear Box Replacing the RotorDismounting the Rotor Mounting the Rotor Replacing the Main BearingsDismounting the Main Bearings Mounting the Main Bearings Lubricating the Main BearingsLubrication Intervals Shift Operation Replace Lubricant CheckCheck lubricant quality Replacing or Refilling LubricantRefilling lubricant Replacing LubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Tightening Torque of the Screws Replacing the ScreenHydraulic Screen Support optional Belts Checking the tension force of the V-beltCentres and 16mm sag Profile section Efficiency of x Newton LbsRe-tensioning and relaxing the V-belt Checking V-belt condition, replacing V-beltWorking on the Cutting Knives Replacing and Checking the Cutting Knife MountingsTorque Grade Bolt type Checking the Condition of the CuttersDismounting the Cutters Dismounting the Cutter HoldersDismounting the Bed Knives Mounting the Cutter Holders Make sure that the cutter holder fits properly Mounting the CuttersMake sure the cutter fits planar in the seat Adjust the gap between cutter and bed knife to 0.8-1.0 mm Mounting the Bed KnivesSetting the Cutting Knives Sharpening Cutters and Bed KnivesFix the knife cover plates BJ5-620 Maintenance Hydraulic Maintenance Transporting and Storing the Cutting KnivesHydraulic liquid recommendation Troubleshooting IntroductionProblem Possible Cause Possible Remedy DepartmentToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Warranty Returns AppendixReturned Material Policy Credit ReturnsTechnical Specifications Drawings and Diagrams Cutter mountingBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram Spare Parts List SXSKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Hydraulic Unit Spare Parts List Pos Description Standard SupplierTechnical Assistance Sterling, Inc Th Street New Berlin, WI