Sterling SXS Series specifications Emptying the Screen

Page 28

•Throw the material into the in-feed hopper.

•The machine should be fed from the front.

•If your machine has an additional in-feed device installed, please observe the additional information for working with the in-feed device.

DANGER! Do not climb into the in-feed hopper while operating the machine. Death will result.

Emptying the Screen

1.Switch off the shredder at the main switch.

2.Safeguard main switch using a padlock.

3.Open the machine door.

4.Safeguard machine door.

5.Pivot the screen support downwards by pushing the button screen open on the control box.

6.Remove the screen.

7.Empty the screen.

8.Put the screen back into the screen support.

9.Pivot the screen support into the working position and fasten using the mounting screws.

10.Close the machine.

11.Shredder can be started again.

4

1

BJ5-620

Operation

2

(1)Hydraulic cylinder

(2)Screen support

(3)Screen

(4)Rotor

3

28 of 73

Image 28

Contents SXS Extreme Duty Shredder Shipping Info Storage, Disposal, Transportation StorageDisposal TransportationTable of Contents How to Use This Manual SafetySafety Symbols Used in this Manual General Safety Regulations ResponsibilityPage Remaining Risks BJ5-620 Safety Page Functional Description Models Covered in This ManualGeneral Description Mechanical SectionMachine Standard Execution Typical Features and ComponentsMaterial In-feed In-feed Hopper Additional In-feed DeviceRotor, Cutters, and Bed Knives DriveRotor, cutters, bed knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Belts and Ram Guards Safety MarkingsPersonal Protective Gear Emergency Stop Button Re-operationInstallation Unloading and Installing the MachineUncrating the Equipment Requirements at Application SiteElectrical Connections Connection of Emergency Stop Button General Advice Initial Start-upChecking the Rotational Direction Machine Check Prior to Start-upPage Operation Operation ProceduresStart-up Emptying the Screen Hydraulic Set-up 12ml / r ec Switch OFF Machine Shut-downPreventative Maintenance Schedule MaintenanceMaintenance Plan Cleaning the Machine Preventative and Corrective MaintenanceChecking the Protective Devices Replacing the Rotor Replacing the Gear BoxDismounting the Rotor Replacing the Main Bearings Mounting the RotorDismounting the Main Bearings Mounting the Main Bearings Lubricating the Main BearingsLubrication Intervals Shift Operation Replace Lubricant CheckCheck lubricant quality Replacing or Refilling LubricantRefilling lubricant Replacing LubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Replacing the Screen Tightening Torque of the ScrewsHydraulic Screen Support optional Belts Checking the tension force of the V-beltCentres and 16mm sag Profile section Efficiency of x Newton LbsRe-tensioning and relaxing the V-belt Checking V-belt condition, replacing V-beltWorking on the Cutting Knives Replacing and Checking the Cutting Knife MountingsTorque Grade Bolt type Checking the Condition of the CuttersDismounting the Cutters Dismounting the Cutter HoldersDismounting the Bed Knives Mounting the Cutter Holders Mounting the Cutters Make sure that the cutter holder fits properlyMake sure the cutter fits planar in the seat Adjust the gap between cutter and bed knife to 0.8-1.0 mm Mounting the Bed KnivesSetting the Cutting Knives Sharpening Cutters and Bed KnivesFix the knife cover plates BJ5-620 Maintenance Hydraulic Maintenance Transporting and Storing the Cutting KnivesHydraulic liquid recommendation Troubleshooting IntroductionProblem Possible Cause Possible Remedy DepartmentToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Warranty Returns AppendixReturned Material Policy Credit ReturnsTechnical Specifications Drawings and Diagrams Cutter mountingBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram Spare Parts List SXSKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Hydraulic Unit Spare Parts List Pos Description Standard SupplierTechnical Assistance Sterling, Inc Th Street New Berlin, WI