Sterling SXS Series specifications Dismounting the Bed Knives

Page 46

6.Clean the hexagon head socket of the cutter mounting screw (2).

7.Loosen the bolt using a high quality Allen key (10 mm). If necessary knock the Allen key lightly with a hammer to loosen it.

8.Take out the cutter mounting screw, the washer and the cutter.

9.Clean the hexagon head socket of the knife holder fixing bolts (4).

10.Loose the bolt using a high quality Allen key (6 mm). Knock the Allen key lightly with a hammer to loose it if necessary.

11.Take out the cutter holder mounting screws (4).

12.Remove the cutter holder with the delivered Extractor.

NOTE: See drawing in “Dismounting the rotor knives”.

WARNING! Danger of cutting caused by sharp knives at all times—even when rotor is at standstill. Serious Injury especially to the hands and fingers can occur. Wear protective gloves!

Dismounting the Bed Knives

1.Switch OFF the shredder at the main switch.

2.Safeguard main switch using a padlock.

3.Open the hopper door.

4.Safeguard the hopper door.

NOTE: Although it is possible to reach the knives by climbing into the feeding chamber, it is recommended to access the knives through the front side door.

BJ5-620

Maintenance

46 of 73

Image 46

Contents SXS Extreme Duty Shredder Shipping Info Disposal Storage, Disposal, TransportationStorage TransportationTable of Contents How to Use This Manual SafetySafety Symbols Used in this Manual General Safety Regulations ResponsibilityPage Remaining Risks BJ5-620 Safety Page General Description Functional DescriptionModels Covered in This Manual Mechanical SectionMachine Standard Execution Typical Features and ComponentsMaterial In-feed In-feed Hopper Additional In-feed DeviceRotor, Cutters, and Bed Knives DriveRotor, cutters, bed knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Belts and Ram Guards Safety MarkingsPersonal Protective Gear Emergency Stop Button Re-operationUncrating the Equipment InstallationUnloading and Installing the Machine Requirements at Application SiteElectrical Connections Connection of Emergency Stop Button Checking the Rotational Direction General AdviceInitial Start-up Machine Check Prior to Start-upPage Operation Operation ProceduresStart-up Emptying the Screen Hydraulic Set-up 12ml / r ec Switch OFF Machine Shut-downPreventative Maintenance Schedule MaintenanceMaintenance Plan Cleaning the Machine Preventative and Corrective MaintenanceChecking the Protective Devices Replacing the Rotor Replacing the Gear BoxDismounting the Rotor Replacing the Main Bearings Mounting the RotorDismounting the Main Bearings Mounting the Main Bearings Lubricating the Main BearingsCheck lubricant quality Lubrication IntervalsShift Operation Replace Lubricant Check Replacing or Refilling LubricantRefilling lubricant Replacing LubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Replacing the Screen Tightening Torque of the ScrewsHydraulic Screen Support optional Centres and 16mm sag BeltsChecking the tension force of the V-belt Profile section Efficiency of x Newton LbsRe-tensioning and relaxing the V-belt Checking V-belt condition, replacing V-beltTorque Grade Bolt type Working on the Cutting KnivesReplacing and Checking the Cutting Knife Mountings Checking the Condition of the CuttersDismounting the Cutters Dismounting the Cutter HoldersDismounting the Bed Knives Mounting the Cutter Holders Mounting the Cutters Make sure that the cutter holder fits properlyMake sure the cutter fits planar in the seat Adjust the gap between cutter and bed knife to 0.8-1.0 mm Mounting the Bed KnivesSetting the Cutting Knives Sharpening Cutters and Bed KnivesFix the knife cover plates BJ5-620 Maintenance Hydraulic Maintenance Transporting and Storing the Cutting KnivesHydraulic liquid recommendation Troubleshooting IntroductionProblem Possible Cause Possible Remedy DepartmentToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Returned Material Policy Warranty ReturnsAppendix Credit ReturnsTechnical Specifications Drawings and Diagrams Cutter mountingBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram Spare Parts List SXSKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Hydraulic Unit Spare Parts List Pos Description Standard SupplierTechnical Assistance Sterling, Inc Th Street New Berlin, WI