Sterling SXS Series specifications Refilling lubricant, Replacing Lubricant

Page 38

Refilling lubricant

The grease reaches through the circulating grooves and bores via lubrication nipples into the interior of the bearing.

The greasing quantity is .13 to .22 lbs (60 to 100 g) roller bearing grease F3 per bearing.

Grease Nipple

Replacing Lubricant

Renewing the lubricant between intervals is only necessary when there unusual noises or overheating. Mounting and dismounting of the bearings must be carried out in accordance with the instructions in this operation manual (see replacing the bearings).

1.Open the bearing.

2.Remove the bearing housing and the bearing cover.

3.Clean the bearing carefully using petroleum ether.

NOTE: Petroleum ether, petroleum, spirit, aqueous neutral or alkaline cleaning agents may be used to clean the bearings. After washing out, the bearing must immediately be preserved using lubricant, in order to avoid corrosion.

4.Fill bearing with approved lubricant (refer to the “List of Lubricants”).

BJ5-620

Maintenance

38 of 73

Image 38

Contents SXS Extreme Duty Shredder Shipping Info Disposal Storage, Disposal, TransportationStorage TransportationTable of Contents Safety Symbols Used in this Manual SafetyHow to Use This Manual General Safety Regulations ResponsibilityPage Remaining Risks BJ5-620 Safety Page General Description Functional DescriptionModels Covered in This Manual Mechanical SectionMaterial In-feed Typical Features and ComponentsMachine Standard Execution In-feed Hopper Additional In-feed DeviceRotor, cutters, bed knives DriveRotor, Cutters, and Bed Knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Personal Protective Gear Safety MarkingsBelts and Ram Guards Emergency Stop Button Re-operationUncrating the Equipment InstallationUnloading and Installing the Machine Requirements at Application SiteElectrical Connections Connection of Emergency Stop Button Checking the Rotational Direction General AdviceInitial Start-up Machine Check Prior to Start-upPage Start-up Operation ProceduresOperation Emptying the Screen Hydraulic Set-up 12ml / r ec Switch OFF Machine Shut-downMaintenance Plan MaintenancePreventative Maintenance Schedule Checking the Protective Devices Preventative and Corrective MaintenanceCleaning the Machine Dismounting the Rotor Replacing the Gear BoxReplacing the Rotor Dismounting the Main Bearings Mounting the RotorReplacing the Main Bearings Mounting the Main Bearings Lubricating the Main BearingsCheck lubricant quality Lubrication IntervalsShift Operation Replace Lubricant Check Replacing or Refilling LubricantRefilling lubricant Replacing LubricantBJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Hydraulic Screen Support optional Tightening Torque of the ScrewsReplacing the Screen Centres and 16mm sag BeltsChecking the tension force of the V-belt Profile section Efficiency of x Newton LbsRe-tensioning and relaxing the V-belt Checking V-belt condition, replacing V-beltTorque Grade Bolt type Working on the Cutting KnivesReplacing and Checking the Cutting Knife Mountings Checking the Condition of the CuttersDismounting the Cutters Dismounting the Cutter HoldersDismounting the Bed Knives Mounting the Cutter Holders Make sure the cutter fits planar in the seat Make sure that the cutter holder fits properlyMounting the Cutters Adjust the gap between cutter and bed knife to 0.8-1.0 mm Mounting the Bed KnivesSetting the Cutting Knives Sharpening Cutters and Bed KnivesFix the knife cover plates BJ5-620 Maintenance Hydraulic Maintenance Transporting and Storing the Cutting KnivesHydraulic liquid recommendation Troubleshooting IntroductionProblem Possible Cause Possible Remedy DepartmentToo many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Returned Material Policy Warranty ReturnsAppendix Credit ReturnsTechnical Specifications Drawings and Diagrams Cutter mountingBed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram Spare Parts List SXSKnife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Hydraulic Unit Spare Parts List Pos Description Standard SupplierTechnical Assistance Sterling, Inc Th Street New Berlin, WI