Intel ISP1100 manual Removing/Installing the Server in the Rack

Page 25

Installing the Server in the Rack

This procedure describes how to install the server in the rack. Before proceeding, be sure and familiarize yourself with the “Rackmount Precautions” information in the “Before You Begin” section at the front of this chapter. Refer to Figure 5 while performing this procedure.

1.Orient the server with the rackmount brackets aligned with the desired mounting holes (A) in the rack posts (B).

2.Use a Phillips screwdriver and start the two screws removed in the previous “Removing the Server From the Rack” procedure and loosely attach the mounting brackets (one on each side of the server) to the rack posts. Do not tighten.

3.Properly align the server in the rack.

4.Use a Phillips screwdriver and tighten the two screws (C) to securely attach the mounting brackets to the rack posts.

B

A

C

A

C

B

OMO9442

Figure 5. Removing/Installing the Server in the Rack

Removing/Installing Server Components

25

Image 25

Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsServer Board Features Server Board FeaturesFeature DescriptionServer Board Connectors and Components Server Board Connectors and ComponentsFront Panel Controls, Connectors, and IndicatorsBack Panel Memory ProcessorsSupported Processors Memory Error Detection Mode Supported Memory CharacteristicsDimm Type ECC Disabled ECC Enabled Universal Serial Bus ChipsetIDE Support Real-Time Clock, Cmos SRAM, and BatterySerial Ports ControllerDiskette Drive Controller Keyboard and Mouse Interface Hardware MonitorFan Tachometer MUX Control Mapping FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH InputIntel Pro/100+ Server 82559 Ethernet Controllers Scsi Hard Drive LED ConnectorWake on LAN Wake on Ring Wake on Ring/Resume on RingResume on Ring SMI and NMI Routing Power ConnectorSpeaker SMI and NMI RoutingConnector Fan Connector DescriptionsFan Support FunctionFCC/Emissions Disclaimer Before You BeginElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Safety Compliance Safety and Regulatory RequirementsTools and Supplies Needed Removing the Server From the RackRemoving/Installing the Server in the Rack Installing the Server in the RackReplacing the Cover Removing the CoverRemoving the Processor Heat Sink Removing the ProcessorRemoving the Processor Chip Installing the ProcessorRemoving the Processor Fan Removing the Processor Fan If ApplicableInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drive in the Mounting Bracket Installing the Hard DrivesInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the Drive in the Mounting Bracket Installing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the Filler Panel Retention Bracket Removing the PCI Add-in CardsRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards from the Riser Removing the Add-in Cards From the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsRemoving the Riser Card Installing PCI Add-in CardsRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsVarning Replacing the Back-up BatteryReplacing the Lithium Back-up Battery Power Cord Requirements Power Up the ServerPowering Up the Server Removing/Installing Server Components Configuration Utilities Power-On Self-Test PostHot Keys Hot KeysBios Setup Menu Bar Using Bios SetupBios Setup Function Keys DescriptionAdvanced Main MenuMain Menu Boot Configuration Submenu Advanced Menu Feature OptionsPeripheral Configuration Submenu Advanced MenuIDE Configuration Submenu IDE Configuration MenuOptions Boot default Sectors default DescriptionEvent Log Configuration Submenu Diskette Configuration SubmenuOptions Auto default Disabled default 44/1.25MB 3.5 defaultBoot Boot MenuBoot Menu Security MenuStay Off default Last State defaultPower On default Stay Off default 1st IDE defaultSystem Management System Management MenuSystem Management Menu Preparing for the Upgrade Upgrading the BiosExit Menu Exit MenuObtaining the Upgrade Utility Recovering the Bios Performing the UpgradeIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Checklist Resetting the SystemInitial System Startup PressAfter the System Has Been Running Correctly Running New Application SoftwarePreparing the System for Diagnostic Testing More Problem Solving ProceduresMonitoring Post Verifying Proper Operation of Key System LightsPower Light Does Not Light Specific Problems and Corrective ActionsNo Characters Appear on Screen System Cooling Fans Do Not Rotate Properly Characters Are Distorted or IncorrectDiskette Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not LightCannot Connect to a Server Problems with Network Problems with Application SoftwareError and Informational Messages Bootable CD-ROM Is Not DetectedError Codes and Error Messages Beeps Error messageError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index