Intel manual Intel ISP1100 Internet Server Product Guide

Page 66

8.Two beeps and the end of activity in drive A indicate successful BIOS recovery.

9.A series of continuous beeps indicates failed BIOS recovery.

10.If recovery fails, return to step 1 and repeat the recovery process.

11.If recovery is successful, turn off the computer. Remove the computer cover and continue with the following steps.

12.Set the BIOS configuration jumper to pins 1-2.

13.Replace the computer cover. Leave the upgrade disk in drive A and turn on the computer.

14.Continue with the BIOS upgrade (see “Upgrading the BIOS” on page 54).

66	Intel ISP1100 Internet Server Product Guide

Image 66

Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsFeature Server Board FeaturesServer Board Features DescriptionServer Board Connectors and Components Server Board Connectors and ComponentsControls, Connectors, and Indicators Front PanelBack Panel Processors MemorySupported Processors Supported Memory Characteristics Memory Error Detection ModeDimm Type ECC Disabled ECC Enabled Chipset Universal Serial BusReal-Time Clock, Cmos SRAM, and Battery IDE SupportController Serial PortsDiskette Drive Controller Fan Tachometer MUX Control Mapping Hardware MonitorKeyboard and Mouse Interface FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH InputScsi Hard Drive LED Connector Intel Pro/100+ Server 82559 Ethernet ControllersWake on LAN Wake on Ring/Resume on Ring Wake on RingResume on Ring Speaker Power ConnectorSMI and NMI Routing SMI and NMI RoutingFan Support Fan Connector DescriptionsConnector FunctionBefore You Begin FCC/Emissions DisclaimerElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Tools and Supplies Needed Safety and Regulatory RequirementsSafety Compliance Removing the Server From the RackInstalling the Server in the Rack Removing/Installing the Server in the RackRemoving the Cover Replacing the CoverRemoving the Processor Removing the Processor Heat SinkInstalling the Processor Removing the Processor ChipRemoving the Processor Fan If Applicable Removing the Processor FanInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drives Installing the Hard Drive in the Mounting BracketInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive Installing the Drive in the Mounting BracketInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the PCI Add-in Cards Removing the Filler Panel Retention BracketRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards From the Riser Removing the Add-in Cards from the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsInstalling PCI Add-in Cards Removing the Riser CardRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsReplacing the Back-up Battery VarningReplacing the Lithium Back-up Battery Power Up the Server Power Cord RequirementsPowering Up the Server Removing/Installing Server Components Hot Keys Power-On Self-Test PostConfiguration Utilities Hot KeysBios Setup Function Keys Using Bios SetupBios Setup Menu Bar DescriptionMain Menu AdvancedMain Menu Peripheral Configuration Submenu Advanced Menu Feature OptionsBoot Configuration Submenu Advanced MenuOptions Boot default IDE Configuration MenuIDE Configuration Submenu Sectors default DescriptionOptions Auto default Disabled default Diskette Configuration SubmenuEvent Log Configuration Submenu 44/1.25MB 3.5 defaultBoot Menu Boot MenuBoot Security MenuPower On default Stay Off default Last State defaultStay Off default 1st IDE defaultSystem Management Menu System ManagementSystem Management Menu Exit Menu Upgrading the BiosPreparing for the Upgrade Exit MenuObtaining the Upgrade Utility Performing the Upgrade Recovering the BiosIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Initial System Startup Resetting the SystemChecklist PressRunning New Application Software After the System Has Been Running CorrectlyMonitoring Post More Problem Solving ProceduresPreparing the System for Diagnostic Testing Verifying Proper Operation of Key System LightsSpecific Problems and Corrective Actions Power Light Does Not LightNo Characters Appear on Screen Characters Are Distorted or Incorrect System Cooling Fans Do Not Rotate ProperlyDiskette Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not LightCannot Connect to a Server Problems with Application Software Problems with NetworkError Codes and Error Messages Bootable CD-ROM Is Not DetectedError and Informational Messages Beeps Error messageError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index