Intel ISP1100 manual Removing the Processor Fan If Applicable

Page 29

Removing the Processor Fan (If Applicable)

This procedure describes how to remove the processor fan from a replacement processor. Due to space constraints, the server will not accommodate a processor with a fan mounted on the heat sink. Sufficient cooling is provided in the server without the processor fan.

If the processor you wish to install has a fan mounted on top of the heat sink, remove the fan as described in the following procedure. Otherwise, proceed to “Installing the Processor Chip.” Refer to Figure 9 while performing this procedure.

1.Grasp the fan housing at each corner.

2.Gently press and lift on the corners until the fan releases from the heat sink.

OMO9430

Figure 9. Removing the Processor Fan

Removing/Installing Server Components

29

Image 29

Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsServer Board Features Server Board FeaturesFeature DescriptionServer Board Connectors and Components Server Board Connectors and ComponentsBack Panel Controls, Connectors, and IndicatorsFront Panel Supported Processors ProcessorsMemory Dimm Type ECC Disabled ECC Enabled Supported Memory CharacteristicsMemory Error Detection Mode Universal Serial Bus ChipsetIDE Support Real-Time Clock, Cmos SRAM, and BatteryDiskette Drive Controller ControllerSerial Ports Keyboard and Mouse Interface Hardware MonitorFan Tachometer MUX Control Mapping FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH InputWake on LAN Scsi Hard Drive LED ConnectorIntel Pro/100+ Server 82559 Ethernet Controllers Resume on Ring Wake on Ring/Resume on RingWake on Ring SMI and NMI Routing Power ConnectorSpeaker SMI and NMI RoutingConnector Fan Connector DescriptionsFan Support FunctionFCC/Emissions Disclaimer Before You BeginElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Safety Compliance Safety and Regulatory RequirementsTools and Supplies Needed Removing the Server From the RackRemoving/Installing the Server in the Rack Installing the Server in the RackReplacing the Cover Removing the CoverRemoving the Processor Heat Sink Removing the ProcessorRemoving the Processor Chip Installing the ProcessorRemoving the Processor Fan Removing the Processor Fan If ApplicableInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drive in the Mounting Bracket Installing the Hard DrivesInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the Drive in the Mounting Bracket Installing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the Filler Panel Retention Bracket Removing the PCI Add-in CardsRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards from the Riser Removing the Add-in Cards From the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsRemoving the Riser Card Installing PCI Add-in CardsRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsVarning Replacing the Back-up BatteryReplacing the Lithium Back-up Battery Power Cord Requirements Power Up the ServerPowering Up the Server Removing/Installing Server Components Configuration Utilities Power-On Self-Test PostHot Keys Hot KeysBios Setup Menu Bar Using Bios SetupBios Setup Function Keys DescriptionMain Menu Main MenuAdvanced Boot Configuration Submenu Advanced Menu Feature OptionsPeripheral Configuration Submenu Advanced MenuIDE Configuration Submenu IDE Configuration MenuOptions Boot default Sectors default DescriptionEvent Log Configuration Submenu Diskette Configuration SubmenuOptions Auto default Disabled default 44/1.25MB 3.5 defaultBoot Boot MenuBoot Menu Security MenuStay Off default Last State defaultPower On default Stay Off default 1st IDE defaultSystem Management Menu System Management MenuSystem Management Preparing for the Upgrade Upgrading the BiosExit Menu Exit MenuObtaining the Upgrade Utility Recovering the Bios Performing the UpgradeIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Checklist Resetting the SystemInitial System Startup PressAfter the System Has Been Running Correctly Running New Application SoftwarePreparing the System for Diagnostic Testing More Problem Solving ProceduresMonitoring Post Verifying Proper Operation of Key System LightsNo Characters Appear on Screen Specific Problems and Corrective ActionsPower Light Does Not Light Diskette Drive Activity Light Does Not Light Characters Are Distorted or IncorrectSystem Cooling Fans Do Not Rotate Properly Cannot Connect to a Server Hard Disk Drive Activity Light Does Not LightCD-ROM Drive Activity Light Does Not Light Problems with Network Problems with Application SoftwareError and Informational Messages Bootable CD-ROM Is Not DetectedError Codes and Error Messages Beeps Error messageError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index