Intel ISP1100 manual Installing the Hard Drive in the Drive Bay

Page 36

Installing the Hard Drive in the Drive Bay

Perform this procedure to install the mounting bracket with the hard drive in the drive bay. Refer to Figure 16 while performing this procedure.

1.Connect the power and data cables to the back of the drive (D).

2.Position the drive in the server drive bay so that the end of the bracket with the tabs (A) is facing the server front panel.

3.Gently guide the bracket tabs into the mating slots (B) in the server front panel.

4.Align the two holes in the back of the bracket with the two chassis snaptop standoffs (C).

5.Press down on the back of the mounting bracket until the two snaptop standoffs snap into the mating holes in the bracket.

B

D

A

C

OMO9436

Figure 16. Installing the Hard Drive in the Drive Bay

36	Intel ISP1100 Internet Server Product Guide

Image 36

Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsServer Board Features Server Board FeaturesFeature DescriptionServer Board Connectors and Components Server Board Connectors and ComponentsControls, Connectors, and Indicators Front PanelBack Panel Processors MemorySupported Processors Supported Memory Characteristics Memory Error Detection ModeDimm Type ECC Disabled ECC Enabled Chipset Universal Serial BusReal-Time Clock, Cmos SRAM, and Battery IDE SupportController Serial PortsDiskette Drive Controller Hardware Monitor Keyboard and Mouse InterfaceFan Tachometer MUX Control Mapping FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH InputScsi Hard Drive LED Connector Intel Pro/100+ Server 82559 Ethernet ControllersWake on LAN Wake on Ring/Resume on Ring Wake on RingResume on Ring Power Connector SMI and NMI RoutingSpeaker SMI and NMI RoutingFan Connector Descriptions ConnectorFan Support FunctionBefore You Begin FCC/Emissions DisclaimerElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Safety and Regulatory Requirements Safety ComplianceTools and Supplies Needed Removing the Server From the RackInstalling the Server in the Rack Removing/Installing the Server in the RackRemoving the Cover Replacing the CoverRemoving the Processor Removing the Processor Heat SinkInstalling the Processor Removing the Processor ChipRemoving the Processor Fan If Applicable Removing the Processor FanInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drives Installing the Hard Drive in the Mounting BracketInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive Installing the Drive in the Mounting BracketInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the PCI Add-in Cards Removing the Filler Panel Retention BracketRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards From the Riser Removing the Add-in Cards from the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsInstalling PCI Add-in Cards Removing the Riser CardRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsReplacing the Back-up Battery VarningReplacing the Lithium Back-up Battery Power Up the Server Power Cord RequirementsPowering Up the Server Removing/Installing Server Components Power-On Self-Test Post Configuration UtilitiesHot Keys Hot KeysUsing Bios Setup Bios Setup Menu BarBios Setup Function Keys DescriptionMain Menu AdvancedMain Menu Advanced Menu Feature Options Boot Configuration SubmenuPeripheral Configuration Submenu Advanced MenuIDE Configuration Menu IDE Configuration SubmenuOptions Boot default Sectors default DescriptionDiskette Configuration Submenu Event Log Configuration SubmenuOptions Auto default Disabled default 44/1.25MB 3.5 defaultBoot Menu BootBoot Menu Security MenuLast State default Stay Off defaultPower On default Stay Off default 1st IDE defaultSystem Management Menu System ManagementSystem Management Menu Upgrading the Bios Preparing for the UpgradeExit Menu Exit MenuObtaining the Upgrade Utility Performing the Upgrade Recovering the BiosIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Resetting the System ChecklistInitial System Startup PressRunning New Application Software After the System Has Been Running CorrectlyMore Problem Solving Procedures Preparing the System for Diagnostic TestingMonitoring Post Verifying Proper Operation of Key System LightsSpecific Problems and Corrective Actions Power Light Does Not LightNo Characters Appear on Screen Characters Are Distorted or Incorrect System Cooling Fans Do Not Rotate ProperlyDiskette Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not LightCannot Connect to a Server Problems with Application Software Problems with NetworkBootable CD-ROM Is Not Detected Error and Informational MessagesError Codes and Error Messages Beeps Error messageError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index