Intel ISP1100 manual Upgrading the Bios, Exit Menu, Preparing for the Upgrade

Page 63

Exit Menu

The menu bar is shown below.


Main	Advanced

Security

Boot

System

Management

Exit

Table 23 shows the Exit menu. This menu exits the Setup program – saving, discarding, and loading default settings.

Table 23. Exit Menu

Feature	Options

Exit Saving Changes	No options
Exit Discarding	No options
Changes
Load Setup Defaults	No options
Load Custom	No options
Defaults
Save Custom	No options
Defaults
Discard Changes	No options

Description

Exits system Setup and saves your changes in CMOS.

Exits system setup without saving your changes in CMOS.

Loads setup defaults.

Loads custom defaults.

Save custom defaults.

Discards changes.

Upgrading the BIOS

Preparing for the Upgrade

Before you upgrade the BIOS, prepare for the upgrade by recording the current BIOS settings, obtaining the upgrade utility, and making a copy of the current BIOS.

Recording the Current BIOS Settings

1. Boot the computer and press <F2> when you see the message:

Press <F2> Key if you want to run SETUP

2. Write down the current settings in the BIOS Setup program.

NOTE

Do not skip step 2. You will need these settings to configure your computer at the end of the procedure.

Configuration Software and Utilities

63

Image 63

Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsDescription Server Board FeaturesServer Board Features FeatureServer Board Connectors and Components Server Board Connectors and ComponentsControls, Connectors, and Indicators Front PanelBack Panel Processors MemorySupported Processors Supported Memory Characteristics Memory Error Detection ModeDimm Type ECC Disabled ECC Enabled Universal Serial Bus ChipsetIDE Support Real-Time Clock, Cmos SRAM, and BatteryController Serial PortsDiskette Drive Controller FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH Input Hardware MonitorKeyboard and Mouse Interface Fan Tachometer MUX Control MappingScsi Hard Drive LED Connector Intel Pro/100+ Server 82559 Ethernet ControllersWake on LAN Wake on Ring/Resume on Ring Wake on RingResume on Ring SMI and NMI Routing Power ConnectorSMI and NMI Routing SpeakerFunction Fan Connector DescriptionsConnector Fan SupportFCC/Emissions Disclaimer Before You BeginElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Removing the Server From the Rack Safety and Regulatory RequirementsSafety Compliance Tools and Supplies NeededRemoving/Installing the Server in the Rack Installing the Server in the RackReplacing the Cover Removing the CoverRemoving the Processor Heat Sink Removing the ProcessorRemoving the Processor Chip Installing the ProcessorRemoving the Processor Fan Removing the Processor Fan If ApplicableInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drive in the Mounting Bracket Installing the Hard DrivesInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the Drive in the Mounting Bracket Installing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the Filler Panel Retention Bracket Removing the PCI Add-in CardsRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards from the Riser Removing the Add-in Cards From the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsRemoving the Riser Card Installing PCI Add-in CardsRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsVarning Replacing the Back-up BatteryReplacing the Lithium Back-up Battery Power Cord Requirements Power Up the ServerPowering Up the Server Removing/Installing Server Components Hot Keys Power-On Self-Test PostConfiguration Utilities Hot KeysDescription Using Bios SetupBios Setup Menu Bar Bios Setup Function KeysMain Menu AdvancedMain Menu Advanced Menu Advanced Menu Feature OptionsBoot Configuration Submenu Peripheral Configuration SubmenuSectors default Description IDE Configuration MenuIDE Configuration Submenu Options Boot default44/1.25MB 3.5 default Diskette Configuration SubmenuEvent Log Configuration Submenu Options Auto default Disabled defaultSecurity Menu Boot MenuBoot Boot Menu1st IDE default Last State defaultStay Off default Power On default Stay Off defaultSystem Management Menu System ManagementSystem Management Menu Exit Menu Upgrading the BiosPreparing for the Upgrade Exit MenuObtaining the Upgrade Utility Recovering the Bios Performing the UpgradeIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Press Resetting the SystemChecklist Initial System StartupAfter the System Has Been Running Correctly Running New Application SoftwareVerifying Proper Operation of Key System Lights More Problem Solving ProceduresPreparing the System for Diagnostic Testing Monitoring PostSpecific Problems and Corrective Actions Power Light Does Not LightNo Characters Appear on Screen Characters Are Distorted or Incorrect System Cooling Fans Do Not Rotate ProperlyDiskette Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not LightCannot Connect to a Server Problems with Network Problems with Application SoftwareBeeps Error message Bootable CD-ROM Is Not DetectedError and Informational Messages Error Codes and Error MessagesError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index