Intel ISP1100 Scsi Hard Drive LED Connector, Intel Pro/100+ Server 82559 Ethernet Controllers

Page 17

For more details on programming and reading the Heceta 2 chip please refer to the Heceta 2 Device Specification version 1.2 or later (see Chapter 13 in the Intel ISP1100 Internet Server Technical Product Specification for how to obtain this specification).

SCSI Hard Drive LED Connector

The optional SCSI hard drive LED connector is a 1 x 2-pin connector that allows add-in SCSI controller applications to use the same LED as the IDE controller. This connector can be connected to the LED output of the add-in controller card (see Chapter 13 in the Intel ISP1100 Internet Server Technical Product Specification for the location and pinouts of the SCSI hard drive LED connector).

Intel® Pro/100+ Server (82559) Ethernet Controllers

Two Intel Pro/100+ Server (82559) Ethernet controllers provide two 10/100 Base-T interfaces accessible from the back panel (see Chapter 13 in the Intel ISP1100 Internet Server Technical Product Specification for the location and pinouts of the LAN connectors).

The LAN connectors on the back panel do not provide LEDs to indicate transmit/receive activity and speed. Instead, these indicators are routed to four LEDs on the front panel. See “Controls, Connectors, and Indicators” for LED locations and definitions.

Alert on LAN and Wake on LAN features are supported by the TR440BX server board software and the SMBUS interface of the Intel 82559s. See the BIOS specification for information regarding Alert on LAN and Wake on LAN. Also see “Wake on LAN” for more information.

CAUTION

For Wake on LAN, the 5V standby line for the power supply must be capable of delivering +5V ±5% at 720 mA. Failure to provide adequate standby current, when implementing Wake on LAN can damage the power supply.

Wake on LAN

Wake on LAN enables remote wakeup of the computer through a network. If a PCI add-in network interface card (NIC) with remote wakeup capabilities is desired, the remote wakeup connector on the NIC must be connected to the onboard Wake on LAN connector.

The integrated LAN controllers or the add-in NIC monitors network traffic at the MII interface. Upon detecting a Magic Packet, the LAN controllers or NIC assert a wakeup signal that powers up the computer.

To access this feature, use the optional Wake on LAN connector on the server board. See “Server Board Connectors and Components” for the location and definition of the Wake on LAN connector.

Description

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsServer Board Features Server Board FeaturesFeature DescriptionServer Board Connectors and Components Server Board Connectors and ComponentsBack Panel Controls, Connectors, and IndicatorsFront Panel Supported Processors ProcessorsMemory Dimm Type ECC Disabled ECC Enabled Supported Memory CharacteristicsMemory Error Detection Mode Universal Serial Bus ChipsetIDE Support Real-Time Clock, Cmos SRAM, and BatteryDiskette Drive Controller ControllerSerial Ports Keyboard and Mouse Interface Hardware MonitorFan Tachometer MUX Control Mapping FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH InputWake on LAN Scsi Hard Drive LED ConnectorIntel Pro/100+ Server 82559 Ethernet Controllers Resume on Ring Wake on Ring/Resume on RingWake on Ring SMI and NMI Routing Power ConnectorSpeaker SMI and NMI RoutingConnector Fan Connector DescriptionsFan Support FunctionFCC/Emissions Disclaimer Before You BeginElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Safety Compliance Safety and Regulatory RequirementsTools and Supplies Needed Removing the Server From the RackRemoving/Installing the Server in the Rack Installing the Server in the RackReplacing the Cover Removing the CoverRemoving the Processor Heat Sink Removing the ProcessorRemoving the Processor Chip Installing the ProcessorRemoving the Processor Fan Removing the Processor Fan If ApplicableInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drive in the Mounting Bracket Installing the Hard DrivesInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the Drive in the Mounting Bracket Installing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the Filler Panel Retention Bracket Removing the PCI Add-in CardsRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards from the Riser Removing the Add-in Cards From the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsRemoving the Riser Card Installing PCI Add-in CardsRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsVarning Replacing the Back-up BatteryReplacing the Lithium Back-up Battery Power Cord Requirements Power Up the ServerPowering Up the Server Removing/Installing Server Components Configuration Utilities Power-On Self-Test PostHot Keys Hot KeysBios Setup Menu Bar Using Bios SetupBios Setup Function Keys DescriptionMain Menu Main MenuAdvanced Boot Configuration Submenu Advanced Menu Feature OptionsPeripheral Configuration Submenu Advanced MenuIDE Configuration Submenu IDE Configuration MenuOptions Boot default Sectors default DescriptionEvent Log Configuration Submenu Diskette Configuration SubmenuOptions Auto default Disabled default 44/1.25MB 3.5 defaultBoot Boot MenuBoot Menu Security MenuStay Off default Last State defaultPower On default Stay Off default 1st IDE defaultSystem Management Menu System Management MenuSystem Management Preparing for the Upgrade Upgrading the BiosExit Menu Exit MenuObtaining the Upgrade Utility Recovering the Bios Performing the UpgradeIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Checklist Resetting the SystemInitial System Startup PressAfter the System Has Been Running Correctly Running New Application SoftwarePreparing the System for Diagnostic Testing More Problem Solving ProceduresMonitoring Post Verifying Proper Operation of Key System LightsNo Characters Appear on Screen Specific Problems and Corrective ActionsPower Light Does Not Light Diskette Drive Activity Light Does Not Light Characters Are Distorted or IncorrectSystem Cooling Fans Do Not Rotate Properly Cannot Connect to a Server Hard Disk Drive Activity Light Does Not LightCD-ROM Drive Activity Light Does Not Light Problems with Network Problems with Application SoftwareError and Informational Messages Bootable CD-ROM Is Not DetectedError Codes and Error Messages Beeps Error messageError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index
Top Page Image Contents