Intel ISP1100 manual Installing the 3.5-inch Diskette Drive

Page 38

Installing the 3.5-inch Diskette Drive

This procedure describes how to install the 3.5-inch diskette drive in the server drive bay. Before proceeding, be sure you are thoroughly familiar with the information in “Before You Begin” at the front of this chapter.

Installing the Drive in the Mounting Bracket

Perform this procedure to install the 3.5-inch diskette drive in the mounting bracket. Refer to Figure 18 while performing this procedure.

NOTE

This procedure assumes that the mounting bracket has been removed from the server chassis and the drive removed from the bracket as described in the previous “Removing the 3.5-inch Diskette Drive” procedure.

1.Place the diskette drive in the mounting bracket with the component side down and the front panel facing the front of the mounting bracket.

2.Use a Phillips screwdriver and the four screws (A) removed in the preceding “Removing the 3.5-inch Diskette Drive” procedure (two on each side) to securely attach the mounting bracket to the drive.

A

OMO9456

A

Figure 18. Installing the 3.5-inch Diskette Drive in the Mounting Bracket

38	Intel ISP1100 Internet Server Product Guide

Image 38

Contents Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System ComponentsFeature Server Board FeaturesServer Board Features DescriptionServer Board Connectors and Components Server Board Connectors and ComponentsBack Panel Controls, Connectors, and IndicatorsFront Panel Supported Processors ProcessorsMemory Dimm Type ECC Disabled ECC Enabled Supported Memory CharacteristicsMemory Error Detection Mode Chipset Universal Serial BusReal-Time Clock, Cmos SRAM, and Battery IDE SupportDiskette Drive Controller ControllerSerial Ports Fan Tachometer MUX Control Mapping Hardware MonitorKeyboard and Mouse Interface FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH InputWake on LAN Scsi Hard Drive LED ConnectorIntel Pro/100+ Server 82559 Ethernet Controllers Resume on Ring Wake on Ring/Resume on RingWake on Ring Speaker Power ConnectorSMI and NMI Routing SMI and NMI RoutingFan Support Fan Connector DescriptionsConnector FunctionBefore You Begin FCC/Emissions DisclaimerElectrostatic Discharge ESD and ESD Protection Rackmount Precautions Tools and Supplies Needed Safety and Regulatory RequirementsSafety Compliance Removing the Server From the RackInstalling the Server in the Rack Removing/Installing the Server in the RackRemoving the Cover Replacing the CoverRemoving the Processor Removing the Processor Heat SinkInstalling the Processor Removing the Processor ChipRemoving the Processor Fan If Applicable Removing the Processor FanInstalling the Processor Chip Installing the Processor ChipInstalling the Processor Heat Sink Installing the Processor Heat SinkRemoving the Dimm Boards Removing the Dimm BoardsInstalling the Dimm Boards Installing the Dimm BoardsRemoving the Hard Drives Removing the Hard DrivesInstalling the Hard Drives Installing the Hard Drive in the Mounting BracketInstalling the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive BayRemoving the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette DriveInstalling the 3.5-inch Diskette Drive Installing the Drive in the Mounting BracketInstalling the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive BayRemoving the PCI Add-in Cards Removing the Filler Panel Retention BracketRemoving the Riser and Add-in Cards Removing the Riser and Add-in CardsRemoving the Add-in Cards From the Riser Removing the Add-in Cards from the RiserInstalling the Rear I/O Filler Panels Installing the Rear I/O Filler PanelsInstalling PCI Add-in Cards Removing the Riser CardRemoving/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the RiserRemoving the Rear I/O Filler Panels Removing the Rear I/O Filler PanelsInstalling the Riser and Add-in Cards Installing the Riser and Add-in CardsReplacing the Back-up Battery VarningReplacing the Lithium Back-up Battery Power Up the Server Power Cord RequirementsPowering Up the Server Removing/Installing Server Components Hot Keys Power-On Self-Test PostConfiguration Utilities Hot KeysBios Setup Function Keys Using Bios SetupBios Setup Menu Bar DescriptionMain Menu Main MenuAdvanced Peripheral Configuration Submenu Advanced Menu Feature OptionsBoot Configuration Submenu Advanced MenuOptions Boot default IDE Configuration MenuIDE Configuration Submenu Sectors default DescriptionOptions Auto default Disabled default Diskette Configuration SubmenuEvent Log Configuration Submenu 44/1.25MB 3.5 defaultBoot Menu Boot MenuBoot Security MenuPower On default Stay Off default Last State defaultStay Off default 1st IDE defaultSystem Management Menu System Management MenuSystem Management Exit Menu Upgrading the BiosPreparing for the Upgrade Exit MenuObtaining the Upgrade Utility Performing the Upgrade Recovering the BiosIntel ISP1100 Internet Server Product Guide Configuration Software and Utilities Initial System Startup Resetting the SystemChecklist PressRunning New Application Software After the System Has Been Running CorrectlyMonitoring Post More Problem Solving ProceduresPreparing the System for Diagnostic Testing Verifying Proper Operation of Key System LightsNo Characters Appear on Screen Specific Problems and Corrective ActionsPower Light Does Not Light Diskette Drive Activity Light Does Not Light Characters Are Distorted or IncorrectSystem Cooling Fans Do Not Rotate Properly Cannot Connect to a Server Hard Disk Drive Activity Light Does Not LightCD-ROM Drive Activity Light Does Not Light Problems with Application Software Problems with NetworkError Codes and Error Messages Bootable CD-ROM Is Not DetectedError and Informational Messages Beeps Error messageError Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index