Kodak Printe manual To set the ink preheat time, To set dry EOP

Page 20

VinylJet 36TM Reference Guide

Ink preheat

Cartridge heat settings are optimized for media being printed in a standard office environment. If you are experiencing banding, poor fills, or too much dot gain, and you have tried all other means to correct these conditions, you may want to experiment with the ink preheat settings. These will vary depending on the ambient temperature where the printer is located and the media used.

When you adjust the ink settings, you are increasing or decreasing the heat from the default temperature. Pressing the + (plus) button increases the temperature, pressing - (minus) decreases it. When you have reached the limits of the temperature range, the panel will display either MAX or OFF. These settings are saved in the printer. If you change to a different type of ink, you may need to change the heater settings to accommodate the new ink type.

Only the default setting is recommended. However, if you are working in a cold or dry environment, try turning the heat up for a larger dot size. If the heat is turned up too far, the ink may run or sputter. Settings which are too low may result in reverse ghosting. If you are working in a humid or hot environment, turn the heat down for a smaller dot size. Generally a change of one or two increments is all that is needed.

To set the ink preheat time

1Press Setup/Ink Option/Ink Preheat.

2Choose a preheat value.

3Press OK.

Dry EOP

End of page dry ON enables the printer at the completion of the print job to automati- cally advance the media at the printing speed 12 inches to fully pass the IR heater. The media is then fed back into the printer at 25% of the normal reserve speed to avoid cockling on the retract move. End of Page dry OFF does not perform this at job completion and should be used when multiple plots are being printed.

To set dry EOP

1Press Setup/Ink Option/EOP Dry.

2Choose On.

3Press OK.

2-8 Printer Options

Image 20
Contents Text P/N Revision HistoryWarranty Claims FCC Statement U.S.A VDE statementIndustry Canada Material safety data sheetGeneral operating safety For your safety Manual conventions Other reference materialsContents Appendix a Installing additional memory Appendix C Technical information Appendix D Error messagesAppendix E Troubleshooting Appendix B Menu treePrinter setup Use the right inks and media PrintingObtaining quality results Caring for your media Caring for your ink and cartridgesChoose the right media Choose the correct printing mode Use the right softwareReturning to the default settings Printing the settingsPrinter options Important notes about image size vs. dpiChoosing quality mode options Color modeTo choose the color mode To choose print quality Choosing feed media optionsMedia counter To enter a media length valueTo reset the media counter Auto-load delayTo set auto-load delay To display the current valueDefining user setup Save mediaTo turn off Save Media Auto-WipeTo save user setup To use a previously saved user settingChoosing a language To choose a languageTo set ink reduction To set LCD contrastChoosing ink options To set the ink preheat time To set dry EOPPrinter default settings User Settings Default Other OptionsTo print a file using the Windows driver PrintingEnd of Print function Printing modes Printing vector dataAccessing HP-GL/2 features To access HP-GL/2 featuresPalette select To choose a palette typeTo set control ControlRotation To make multiple prints ReprintsTo rotate the image Nesting To define nesting wait time To enable nestingNest time To enable the ink limit Ink limitInstalling additional memory Simm installationAcceptable Simm sizes To remove the right coverTo install the new Simm To remove the SIMMsMenu tree Main menu at a glanceMain menu Feed media menuSetup menu at a glance Bold indicates the default Utility menu at a glance Bold indicates the default Setup menu Print ModeHP-GL/2 Menu Ink Option Menu Serial Comm Menu Bold indicates the default Utility menuPrime menu Service Menu Bold indicates the default Technical information Media Roll ParametersTechnical information C-2 Error messages Cartridge errorsMemory Errors Isolating problems TroubleshootingETroubleshooting quick list Printer health File will not print Printer front view Ink cartridges do not fire properly Firmware Download Procedure Upgrade/Printer Refresh Overall print quality is poor Calibrate cartridges Data Transfer No output when printing from Unix Application Software Difficulty generating prints ranging from a to D size Calling for Help Customer Technical Support